Skip to content

Washing machine repair services

Washer dryer repairs for combo machines

Washer dryer repairs at your home cover both halves of a combo machine: the drying side that won't heat or leaves clothes damp, and the washing side that won't drain, spin or unlock. The technician tests both and quotes before any work starts.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
Illustration of a washer dryer with warm air rising from the drum and a stack of folded towels
On this page
  1. How a washer-dryer dries your washing
  2. Drying faults, by symptom
  3. Why drying needs the tap and the drain
  4. Drying programmes, explained
  5. Washing faults on a washer-dryer
  6. What the technician checks
  7. Built-in washer-dryers
  8. Getting good results from a washer-dryer
  9. Is a washer-dryer worth repairing?
  10. Washer-dryer brands we repair

How a washer-dryer dries your washing

A washer-dryer is a front loader with a drying system built into the same cabinet. That makes it a good fit for flats and townhouses with no room for a separate tumble dryer, but it also means extra parts: a drying heater, a fan, an air duct, a condenser, and the thermostats and sensors that control them.

After the final spin, the fan blows air across the drying heater and into the drum, where it picks up moisture from the clothes as they tumble. On most washer-dryers the damp air then passes through a condenser, where a trickle of cold water cools it so the moisture turns back into water and drains away through the pump. The drier air goes back over the heater and round again.

Thermostats and a thermal cut-out stop the heater overheating, and on sensor programmes, sensors in the drum or the air duct tell the control board when the washing is dry. Most machines finish with a cool-down, when the heater switches off and the drum keeps turning for a while.

Drying faults, by symptom

The drum turns but the clothes stay cold and damp

No heat usually means the drying heater has failed, or a thermostat or thermal cut-out has tripped or failed and cut the power to it. A fan that has stopped, or a fault in the part of the control board that switches the heater, gives a similar result. These are electrical parts that need testing by a technician.

Clothes come out hot but still wet

If there's heat but the moisture isn't leaving, the air isn't being dried. Lint packed into the air duct or condenser, condensing water that has stopped flowing, or a fan that runs slowly can all cause it.

Drying takes far too long, or stops early

An overloaded drum, a low spin speed before drying, or a mix of heavy cottons and light synthetics can make drying slow and uneven. If loads that used to dry well now take much longer, or the machine stops while the clothes are still damp, a dryness or temperature sensor may be reading wrongly.

A hot or burning smell, or the power trips

Lint that builds up near the heater can scorch, and a drying heater with an internal fault can trip the earth leakage the moment it comes on.

Safety first: if a washer-dryer smells of burning, trips the power or feels hot on the outside of the cabinet, switch it off at the wall and unplug it, and don't use it again until a technician has checked it. Drying systems run hot, so please don't attempt any repair to the heating parts yourself.

Why drying needs the tap and the drain

Because most washer-dryers use cold water to condense the moisture out of the drying air, the drying side depends on the water supply as much as the washing side does. On many machines the condenser has its own outlet on the inlet valve, so a closed tap, a blocked inlet filter or a fault in that part of the valve can stop the condensing and leave the washing hot and damp.

The condenser water leaves through the drain pump, together with the moisture taken out of the clothes. A drain fault can therefore stop the drying as well as the wash, which is why a drying fault is always checked against the drain too.

Drying programmes, explained

Most washer-dryers offer two ways to dry. A sensor programme dries to the level you choose, such as cupboard dry or iron dry, and stops when the sensors say the washing has reached it. A timed programme simply runs for the time you set, which suits a few items or a load that needs a little longer.

Many machines also have a wash and dry programme that washes and dries a small load in one go, and a lower drying temperature for synthetics. Your manual gives the load size for each programme, and sticking to it is the easiest way to get dry clothes in a sensible time.

Washing faults on a washer-dryer

The washing side of a washer-dryer is a front loader, so it can develop the same faults as any other front loader: a machine that won't drain, a door that won't open, leaks from the door seal or hoses, worn bearings and, on machines with a brushed motor, worn carbon brushes. Our page on front loader repairs covers those faults in detail, and the technician can look at both sides of the machine on the same visit.

What the technician checks

A drying fault is traced step by step. The technician runs a short drying programme to see whether the heater warms up and the fan moves air, then checks that the condensing water flows and looks for lint in the duct and condenser. It helps to say how long a load takes to dry now compared with when the machine was newer, and whether the problem affects every load or only big ones.

With the machine switched off and unplugged, the heater, thermostats, cut-outs and sensors are tested, along with the pump and the wiring to the drying parts. You get a quote before any work starts, and the repair is proved with a drying run as well as a wash.

Built-in washer-dryers

An integrated washer-dryer sits in a kitchen housing behind a cabinet door. To repair it, the machine is disconnected, slid out of the housing and refitted afterwards, with the door alignment and the hoses checked so nothing is pinched on the way back in. That adds time to the visit, so mention it when you book.

Getting good results from a washer-dryer

  • Dry no more than the drying capacity for your model, and split a full wash into two drying loads if you need to.
  • Spin at the highest speed the fabrics allow before drying, so there's less water to remove.
  • Dry heavy cottons and towels separately from light synthetics, which dry much faster.
  • If your model has a lint filter, clean it after every drying programme as the manual describes.
  • Follow the care labels, and never dry rubber-backed mats, foam items or anything stained with oil, petrol or solvents, which can be a fire risk.
  • Keep the tap open during drying as well as washing, and leave the door open afterwards so the drum and seal can air, as long as no young child or pet can get to it.

Is a washer-dryer worth repairing?

Usually, when the fault is a heater, thermostat, fan or sensor, because those are replaceable parts and the machine does two jobs. If the drying side fails on an older machine that also needs bearings or a control board, compare the total with the price of a new washer-dryer, or of a separate washing machine and tumble dryer if you have the space. Our repair or replace guide can help you decide.

The call-out fee is R300, only payable if you decide not to go ahead with the quote. Repairs carry a 6-month warranty on parts and labour, and our guide to repair costs explains how a price is put together.

Washer-dryer brands we repair

We repair washer-dryers from all major brands, including LG, Samsung, Bosch, Siemens, AEG and Hisense, both freestanding and built in. Have the model number ready when you book a washer dryer repair: it's on a sticker around the door opening or on the back of the machine, and it tells the technician which drying parts your machine uses.

Four simple steps

How it works

  1. Contact us

    Call or WhatsApp with your machine brand and what it is doing. A photo of the error code helps.

  2. A technician comes out

    We book a time that suits you, and on urgent call-outs we aim to arrive within 1 hour, depending on where the technician is working.

  3. Diagnose and quote

    We find the fault and give you a clear price before any work. The R300 call-out fee is only payable if you decide not to go ahead with the quote.

  4. Repair

    Most repairs are done on the spot when the part is available, and every repair carries our 6-month warranty.

Questions and answers

Washer-dryer repairs: questions we get asked

Why are my clothes hot but still wet after drying?
The heater is working, but the moist air isn't being dried. A condenser or duct packed with lint, condensing water that isn't flowing, or a slow fan is the usual cause. A technician can find which one it is and clean or replace the part.
Can I keep using the washing side if the dryer has stopped working?
In most cases, yes, as long as the machine isn't tripping the power or smelling of burning. If it does either, switch it off at the wall and leave it off until it has been checked.
Why does my washer-dryer use water while it's drying?
That's normal on most washer-dryers. Cold water runs through the condenser to cool the damp air, so the moisture turns back into water and drains away with it. It's also why the tap needs to stay open for drying.
How much washing can I dry in one go?
Check the drying capacity in your manual or on the machine's label, because on most models it's smaller than the washing capacity. Drying more than that leaves damp patches and makes the cycle much longer. After a full wash, take part of the load out and dry it in two batches.
Why does my washer-dryer stop before the clothes are dry?
On sensor programmes the machine stops when it decides the load is dry, so a mixed load can fool it: light items dry first while heavy ones stay damp. Try drying similar fabrics together, or use a timed programme. If every load stops early, a sensor may be faulty.
Is it safe to leave a washer-dryer drying while I'm out?
It's safest not to. Standard fire safety advice is not to leave a washing machine or tumble dryer running overnight or while you're out, and a washer-dryer is both. Keep the area around it clear, and switch it off at the wall if it ever smells of burning.
Why is there lint on my clothes after drying?
Lint builds up in the duct and condenser over time and can be blown back onto the washing. Dry towels separately from dark clothes, and clean the lint filter if your model has one. If lint keeps appearing, the condenser and duct may need cleaning by a technician.
Why does the drum keep turning after the drying time has run out?
That's usually the cool-down at the end of the programme. The heater switches off while the drum keeps tumbling, which cools the washing and cuts down creasing. If the machine never seems to finish the cool-down, or the door stays locked long after it, the sensors or the door lock may need checking.

Book a technician

Washing machine broken? Let's get it fixed.

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za