Skip to content

Common washing machine problems

Washing machine not filling with water

A washing machine not filling with water usually has a supply problem: a closed tap, low pressure, a kinked hose or a blocked inlet filter. If water reaches the machine but doesn't go in, the inlet valve, door lock or water level sensor is the next suspect.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. How a machine fills
  2. Signs it's a filling problem
  3. Likely causes
  4. Safe checks you can do
  5. Overfilling, or draining while filling
  6. When to call a technician
  7. What the technician checks and fixes
  8. How long it usually takes
  9. Preventing filling problems
  10. Get the water flowing again

How a machine fills

When you start a programme, a front loader locks its door first. The control board then opens an electric inlet valve at the back, where the hose connects, and water runs through the detergent drawer, picking up the powder or liquid on its way into the drum. A pressure sensor tells the board when the right level is reached, and the valve closes.

Many machines have more than one valve, or a valve with several sections, so water can be sent to different compartments of the drawer. The board also times the fill. If the level isn't reached in the time allowed, most machines stop and show a water supply code (Samsung's 4C code is a well-known example), or simply sit and hum.

Signs it's a filling problem

  • The machine hums or clicks after you press Start, but you can't hear water running in.
  • It fills, but so slowly that the cycle takes far longer than usual.
  • Detergent is left in the drawer, because not enough water ran through it.
  • The washing comes out dry in places, or barely damp.
  • A water supply code appears, or the programme stops early.
  • Only some compartments of the drawer empty: the softener stays behind, for example.

Likely causes

Supply interruptions and low pressure

Planned maintenance, burst pipes and supply cuts all affect water pressure, and a machine that can't fill in its allowed time gives up. If the taps in the house are weak too, the machine isn't the problem. Your manual lists the minimum water pressure your machine needs.

Tanks, booster pumps and boreholes

Homes that run from a backup tank, a booster pump or a borehole depend on the pump for pressure. If the pump is off, has lost power or is struggling, the machine won't fill properly. This catches people out when the washing machine runs on backup power during load shedding but the pump doesn't. Borehole water can also carry sand that blocks the inlet filter.

A closed or partly closed tap

The washing machine tap is easily knocked half-closed when things are stored under the counter or the machine is pulled out. An old tap can also seize or block inside, and replacing it is a plumber's job.

A kinked or squashed inlet hose

If the machine was pushed back hard against the wall, the inlet hose can be folded or pinched behind it. Old rubber hoses also stiffen with age and kink more easily.

A blocked inlet filter

A small mesh filter sits where the hose connects to the machine, and some hoses have another at the tap end. It catches sand, grit and rust, especially after pipe repairs or an outage, when the water comes back dirty. Once it clogs, water only trickles in.

A faulty inlet valve

The inlet valve is electrically operated. If its coil fails or the valve sticks, no water comes in even with good pressure, and if one section fails, water only reaches some compartments of the drawer. A valve that buzzes without letting water through is a typical sign.

Door lock, level sensor or control board

A front loader won't open the valve until the door lock is confirmed. If the water level sensor or its pressure hose is faulty, the machine can think it's already full and never start filling, and the board that switches the valve can fail too.

Safe checks you can do

Safety first: close the washing machine tap, then switch off at the wall and unplug before you disconnect a hose or touch the filter. Expect a little water when you undo the hose, so keep a towel handy. Don't remove the back panel or test the valve yourself.

  1. Check your water. Open the nearest tap. If the pressure is weak or the water is off, wait for the supply to return. If you're on a tank or borehole, make sure the pump is running.
  2. Open the machine's tap fully. If your machine takes hot water as well as cold, check both taps.
  3. Straighten the hose. Ease the machine forward and make sure the inlet hose isn't kinked or trapped.
  4. Clean the inlet filter as your manual describes. With the tap closed and the machine unplugged, unscrew the hose from the back of the machine, rinse the mesh filter under a tap and refit the hose hand-tight. Open the tap and check for drips.
  5. Close the door firmly and start the programme again.
  6. Note any code and check what it means in your manual or our washing machine error code guides.

Overfilling, or draining while filling

The opposite fault is more urgent. If water keeps coming in after the drum is full, rises up the door glass, or appears in the drum when the machine is off, the inlet valve may be stuck open or the level sensor faulty. Switch off at the wall, close the tap and call a technician.

A machine that fills and drains at the same time, so it never seems to fill, is usually siphoning. That happens when the drain hose is pushed too far down the standpipe, taped in so no air can get in, or sits too low, so the water is pulled straight out again. The hose needs to sit loosely at the height and depth your manual shows, and our washing machine installation service can set it up correctly.

When to call a technician

Book a visit if the supply is good, the tap is open, the hose and filter are clear and the machine still won't fill. The same goes if the valve buzzes but no water comes in, only some compartments of the drawer empty, the machine overfills or the code keeps coming back. If the earth leakage trips at any point, leave the machine off.

What the technician checks and fixes

The technician checks the flow and pressure reaching the machine, then the hose and filters. They test the inlet valve and the signal the board sends to it, check that the door lock confirms, and test the water level sensor and its hose.

  • Faulty inlet valve: replaced with one that matches your model, because valves differ in how many outlets they have and how they're fitted. See washing machine parts replacement.
  • Blocked filter or damaged hose: cleaned or replaced.
  • Level sensor or door lock: replaced, then the machine is run until it has filled to the right level and moved on to the wash.
  • Board fault: repaired or replaced once you've accepted the quote.
  • A supply or tap problem: explained clearly, so you know when a plumber is the right person for it.

Our pages on Hisense, Samsung, Smeg and Miele machines describe their water intake faults in more detail.

How long it usually takes

Most filling faults are found quickly, and a filter clean or a hose fix happens on the spot. An inlet valve is usually fitted on the same visit when the part is available; when one has to be ordered, the technician tells you before you say yes to the repair. Our guide to the cost of a repair covers what the price depends on.

Preventing filling problems

  • Keep the tap fully open while the machine is in use, and close it when you go away.
  • After a water outage or pipe repairs, run a cold tap until the water is clear before you start a wash, so the grit doesn't end up in the filter.
  • Clean the inlet filter once or twice a year, and more often on borehole water.
  • Replace inlet hoses that are cracked, bulging or stiff.
  • Leave a little space behind the machine so the hose can't kink.

Get the water flowing again

Still no water going in? Get in touch to book a technician, who will diagnose it at your home and quote before any work starts. There's a R300 call-out fee, only payable if you decide not to go ahead with the quote. If water is getting in but not out, see washing machine not draining instead.

Questions and answers

Frequently asked questions

Why does my washing machine fill so slowly?
Low water pressure and a partly blocked inlet filter are the usual causes, along with a tap that isn't fully open. A weak or sticking inlet valve can do it too. If the house pressure is normal and the filter is clean, have the valve tested.
Can I use my washing machine during a water outage?
Not reliably. With no water or very low pressure, most machines stop partway through with a water supply code. Wait until the supply is back to normal before you start a wash.
Will a booster pump help with low pressure?
If your home has low pressure most of the time, a pressure pump can help, but that's a plumbing job rather than a washing machine repair. A technician can first confirm whether the machine itself has a fault. That way you don't pay for a pump when the problem is a blocked filter.
Why is detergent left in the drawer after a wash?
Not enough water is flowing through the drawer. Low pressure, a partly blocked inlet filter, a clogged drawer or a failing section of the inlet valve can all cause it. Clean the drawer and the inlet filter first, then have the valve checked if it carries on.
Why does my machine buzz but no water comes in?
The buzz is often the inlet valve being switched on. If no water follows, either nothing is reaching the valve, because of a closed tap, no supply or a blocked filter, or the valve has stuck. Check the tap and the filter, then call a technician.
Why won't my machine take water after a plumber worked on the pipes?
Grit loosened by the work often ends up in the machine's inlet filter, and taps are sometimes left closed afterwards. Check that the tap is fully open and clean the filter as your manual describes. If water still won't go in, have the valve checked.
Should I close the washing machine tap after every wash?
It's a good habit if the tap is easy to reach, because it takes the pressure off the hose and valve between washes. At the very least, close it when you go away for a few days. An old tap that's stiff to turn should be replaced by a plumber.
Does a water supply code mean my inlet valve is broken?
Not necessarily. The code only says the machine didn't fill in time, and a closed tap, low pressure or a blocked filter is more likely than a failed valve. Do the simple checks first, and call if the code comes back.

Book a technician

Still not working? We'll come to you.

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za