Skip to content

Brands we repair

Whirlpool washing machine repairs

A Whirlpool that won't drain, spin or start, or has begun to leak, is diagnosed at your home. Our Whirlpool washing machine repairs cover front loaders, top loaders and washer-dryers across Gauteng, and you get a quote before any work starts.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. Whirlpool machines we repair
  2. Early warning signs
  3. Why a Whirlpool won't drain
  4. Whirlpool faults we repair
  5. Two systems: water and electrics
  6. Safe troubleshooting for Whirlpool owners
  7. Whirlpool error codes
  8. Quote first, then the repair
  9. Whirlpool washer-dryers
  10. Repair, or install a new machine
  11. Looking after your Whirlpool
  12. Areas and booking

Whirlpool machines we repair

Whirlpool is an American appliance maker, and you'll find its washing machines in Gauteng homes in many forms, from older top loaders to current front loaders. Recent Whirlpool front loaders sold in South Africa include models with 6th Sense load sensing and the FreshCare+ freshness feature.

We work on all of them: front loaders and top loaders, belt-driven and direct drive designs, compact machines and washer-dryers, old and new. The model number tells the technician which design yours is, and that decides which parts are involved when something fails.

Early warning signs

Many Whirlpool faults show up as small changes before the machine stops altogether, so it pays to book as soon as you notice one of these:

  • Slow or incomplete draining: water left in the drum, or clothes that come out much wetter than usual.
  • A weak or missing spin: the drum turns but never reaches full speed.
  • Small leaks: a damp patch under the machine after each wash.
  • New noises: grinding, squealing or knocking that wasn't there before.
  • Washing that isn't clean: grey, smelly or still soapy laundry.

If you notice one of these, don't start another load: switch the machine off at the wall, or at the DB board if water has reached the plug or socket, and book a technician. Tell us what you noticed, because a struggling pump or a bearing that has started to grind usually gets worse with every wash.

Why a Whirlpool won't drain

Water left in a Whirlpool's drum is usually held up somewhere between the drum and your household drain. You can rule out the drain hose and the pump filter yourself, using the steps under safe troubleshooting below.

If those are clear, the fault is inside the machine. On front loaders it is usually the drain pump itself, or a blockage in the sump hose that runs from the drum to the pump. On top loaders, a faulty lid switch can stop the machine before the drain-and-spin stage, and on some older belt-driven top loaders a worn or slipping belt affects the pump as well as the spin. Our page on a washing machine that won't drain goes into more detail.

Whirlpool faults we repair

Doors, lids and seals

A faulty door lock stops a front loader from starting, or keeps the door locked after the wash, while a worn lid switch assembly stops a top loader from spinning. A split or perished door seal leaks at the front of a front loader, and debris trapped in the seal can stop the door closing properly. See washing machine door won't open.

Water in and water out

We replace drain pumps, clear blocked hoses and pump filters (the coin trap on some machines), and fix machines that won't fill because of a failed inlet valve or a blocked inlet filter. A machine that leaks can have a loose hose clamp, a cracked hose, a leaking pump or a worn tub seal. See how leaks are traced and fixed.

Drive and spin

No spin can be a worn drive belt, worn carbon brushes, a failed motor or a control fault, and on top loaders a worn coupling, clutch or gearbox. A machine that doesn't finish its cycle may be stuck waiting for water to drain or for the drum to balance. See a machine that stops before the spin.

Agitator problems

On a top loader with a two-part agitator, the top half is driven by small plastic cogs, often called agitator dogs, that wear over time. When they go, the bottom of the agitator still twists but the top half spins freely, and the clothes stop turning over properly. It's a small part and a straightforward repair.

Noise, vibration and the drum

Thumping or walking on spin usually comes from worn suspension, worn bearings or a machine that isn't standing level, and a lopsided load makes it worse. Tub and drum problems, such as a loose drum or a broken drum paddle, are repairable too. See a noisy or shaking machine.

Two systems: water and electrics

A washing machine is really two systems working together. The water side brings water in through the hoses and inlet valve, holds it in the tub and pumps it out through the drain hose. The electrical side is the motor, the heating element, the door lock and the control board that runs the programme.

You can safely look at the water side from the outside: the taps, hoses, filters and drain. The electrical side is a technician's job. Some repair guides online suggest taking off the control panel and testing parts with a multimeter, but that means working on mains-powered parts that can give you a serious shock, and it can damage a board that was working. If your checks of the water side don't find the problem, switch off at the wall and call us.

Safe troubleshooting for Whirlpool owners

Safety first: always switch off at the wall and unplug before you check a hose or a filter. If water has reached the plug or socket, or you'd have to stand in water to reach them, leave them alone and switch off at the DB board instead. If the earth leakage or circuit breaker trips when the machine runs, leave it off and call a technician, because it can indicate a dangerous fault.

It won't start

Check the plug is in and switched on at the wall, that the house has power and that the plug point works (try a lamp in it). Make sure a delayed start or the child lock isn't set, and that the door or lid is properly closed. See washing machine won't turn on.

It won't fill, or fills slowly

Open the tap fully and check the inlet hose for kinks. If your manual shows how, you can clean the small mesh filter where the hose connects: close the tap first, switch off at the wall, unplug the machine and have a cloth ready for drips. If it still fills slowly, our guide to a machine that won't fill covers the other causes.

It won't drain

Straighten the drain hose, check how high it runs and how far it goes into the standpipe, and clean the pump filter as your manual describes, with the machine switched off at the wall and unplugged, towels and a tray down and any hot water left to cool.

It leaks

Switch off at the wall first, or at the DB board if the plug or socket is wet or you'd be standing in water. Then check the hose connections at the tap and at the back of the machine, use less detergent if foam is escaping, and look for socks or hair caught in the door seal.

It won't agitate or spin

Take out some of the load if the drum is packed, untangle sheets wrapped around the agitator, spread the load evenly and close the lid firmly. If it still won't move, the drive or the lid switch needs a technician.

Whirlpool error codes

Whirlpool codes vary a lot between models, ranges and the markets they were made for, so we don't publish one general list. Note the code and the stage the machine had reached, whether it was filling, washing or spinning, and look it up in the manual for your model. If it isn't one you can clear yourself, send us the code with a photo of the model number label, and our guide to a washing machine showing an error code explains what to do in the meantime.

Quote first, then the repair

When the technician has found the fault, you get a quote before any work starts, and the choice is yours. If you go ahead, most repairs are done on the same visit when the part is available; if a part has to be ordered, you'll know before you agree. The call-out fee is R300, only payable if you decide not to go ahead with the quote, and the repair carries our 6-month warranty on parts and labour.

Whirlpool washer-dryers

A Whirlpool washer-dryer can develop the usual washing faults plus a few of its own on the drying side. If it washes well but leaves the laundry damp, check that you're drying a smaller load than you wash, as the manual sets out, and that the drying programme suits the fabric. If it still won't dry, book a technician to test the drying side. See our washer-dryer page.

Repair, or install a new machine

If the repair isn't worth it, for example when the tub is cracked or a part costs nearly as much as a new machine, the technician will say so. If you decide to replace it, we can also install the new machine properly, with the hoses connected, the transit bolts removed and the machine levelled. See washing machine installation and our advice on when a machine is worth replacing.

Looking after your Whirlpool

  • Run a maintenance wash. If you mostly wash at low temperatures, run an empty hot wash about once a month to clear residue and keep smells away. Our article on why your washing machine smells explains where they come from.
  • Measure the detergent. A machine that adjusts the water to the load can use very little on a small wash, so a heavy dose of detergent leaves residue and foam behind.
  • Clean the filter. Clear the pump filter on a front loader every few months, as your manual describes, with the machine unplugged first.
  • Let it breathe. Leave the door or lid open after washing so the drum and seal can dry out, and keep the laundry door closed if you have small children or pets.
  • Check the hoses. Look for bulges, cracks or damp patches at the connections now and then.
  • Protect the electronics. Switch off at the wall during load shedding, and wait for the power to settle before you start a wash.

Areas and booking

We repair Whirlpool washing machines across Johannesburg, Pretoria, Centurion, Sandton, Midrand and the East Rand. Whirlpool is one of the brands covered by our washing machine repairs service, all done at your home.

Phone or WhatsApp 079 895 0496 to book a technician, or use our contact page. The model number is on a label on the machine, often inside the door rim, under the lid or on the back; send a photo of it with any code on the display.

ProServ is an independent repairer. We are not affiliated with, authorised or endorsed by Whirlpool. Whirlpool is a trademark of its owner and is used here only to describe the machines we repair. If your machine is still under the manufacturer's warranty, contact Whirlpool first, because outside repairs may affect that warranty.

Four simple steps

How it works

  1. Contact us

    Call or WhatsApp with your machine brand and what it is doing. A photo of the error code helps.

  2. A technician comes out

    We book a time that suits you, and on urgent call-outs we aim to arrive within 1 hour, depending on where the technician is working.

  3. Diagnose and quote

    We find the fault and give you a clear price before any work. The R300 call-out fee is only payable if you decide not to go ahead with the quote.

  4. Repair

    Most repairs are done on the spot when the part is available, and every repair carries our 6-month warranty.

More brands

Other brands we repair

Questions and answers

Whirlpool washing machine repair questions

Why does my Whirlpool drum move after the wash has finished?
If your machine has FreshCare+, that is the feature at work: it uses steam and gentle movements of the drum to keep the laundry fresh if you can't unload it straight away. If the drum moves on a machine without that feature, or the cycle never ends, book a technician.
What does 6th Sense mean on a Whirlpool?
It is Whirlpool's name for sensors that detect how much laundry is in the drum and adjust the water, energy and programme time to suit. It also means water levels and programme times change from load to load, which is normal and not a fault.
Do you repair older Whirlpool top loaders?
Yes. Worn agitator dogs, a lid switch or a coupling are typical repairs on an older Whirlpool top loader, and the technician checks that the part for your model number can still be found before quoting.
My Whirlpool leaves detergent in the drawer. Why?
The drawer or the siphon in the softener compartment is usually blocked with old detergent, or the water pressure is too low to flush it. Take the drawer out and rinse it, check the tap is fully open and use the right amount of detergent. If it still happens, the inlet valve may not be letting enough water through.
Is my Whirlpool belt-driven or direct drive?
It depends on the model and its age, and the model number tells the technician which design you have. It matters because the faults differ: a belt-driven machine can slip or break its belt, while many direct drive top loaders link the motor to the gearbox through a coupling that wears out instead.
What should I do if a hose bursts on my Whirlpool?
Switch the power off first: at the wall if the plug and socket are dry, or at the DB board, without touching the plug, if they're wet or you'd have to stand in water to reach them. Then close the tap, mop up and look at whether the hose split or came loose at a connection. A split hose has to be replaced, and the technician can fit a new one and check the other hose at the same time.

Book a technician

Whirlpool washing machine playing up?

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za