Skip to content

Common washing machine problems

Washing machine showing an error code

A washing machine showing an error code has stopped because a self-check found something wrong. The code points to the system involved, such as the drain, water supply or door, but not always to the failed part. Here's how to read it and what to do next.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. How error codes work
  2. The main families of codes
  3. What each family usually means
  4. Brand error code guides
  5. Flashing lights instead of a code
  6. Find your model number
  7. Safe first steps
  8. Clearing a code versus fixing it
  9. What the technician does with it
  10. Book a repair

How error codes work

A modern washing machine checks itself all the time. Sensors report the water level, the water temperature, the motor speed and whether the door is locked, and the control board times each stage of the cycle. When a reading falls outside its limits, say the water hasn't drained in the time allowed, the board stops the programme and shows a code. Many machines also keep recent codes in a memory a technician can read.

Each manufacturer sets its own codes, and they can change between models and generations of the same brand. Some aren't faults at all but status messages, such as a reminder that the child lock is on or that the power was interrupted. That's why the model number matters as much as the code.

The main families of codes

Code familyWhat the machine detectedWhere to start
Water supplyThe drum didn't fill to the right level in timeThe tap, the inlet hose and its filter, and your water pressure
DrainThe water didn't pump out in timeThe pump filter, the drain hose and the standpipe
Door or lockThe door isn't confirmed shut and lockedClose the door firmly and check nothing is caught in the seal
ImbalanceThe load is too uneven to spin safelyRearrange the load and check the machine is level
FoamToo many suds in the drumUse less detergent, or the right type
MotorThe drum isn't turning as expectedTake out some washing if the drum is packed, then call a technician
HeatingThe water isn't heating, or the temperature sensor reads wrongNothing for you to check: it's electrical
CommunicationThe boards inside the machine can't talk to each otherSwitch off at the wall for a few minutes, and call a technician if it returns

Some machines add codes for leaks and overflows. Treat those as urgent: switch off at the wall (or at the DB board if the plug or socket is wet or you'd have to stand in water), close the tap and call a technician.

What each family usually means

Water supply and drain codes

These often have a simple cause you can check yourself. Samsung's 4C is a widely documented water supply code. On the drain side, LG's OE, Samsung's 5C and Bosch's E18 all point to water that isn't pumping away. Our guides to a washing machine not filling with water and a washing machine not draining walk you through the checks.

Door, imbalance and foam codes

These usually come down to how the machine is being used, so they're worth a careful look before you call. A door code can be as simple as a sock caught in the seal. Imbalance codes often clear when you spread the load or take out a single heavy item, and foam codes when you cut the dose or switch to a detergent made for automatic machines.

If they keep coming back, see washing machine door won't open or lock or washing machine not spinning.

Motor, heating and communication codes

These point to electrical parts: the motor and its speed sensor, the heating element and temperature sensor, the wiring and the boards. There's nothing safe for an owner to test here, so note the code, and if it comes back after one restart at the wall, leave the machine off and book a technician. If a heating fault also trips the earth leakage, the machine must stay off until it's been checked.

Brand error code guides

We've written guides to the common codes on four brands found in many Gauteng homes:

For other makes, start with your manual and our brand pages for Whirlpool, Hisense, AEG, Siemens, Miele, Smeg and Speed Queen, or send us the code with your model number.

Flashing lights instead of a code

Machines without a digital display show faults with a pattern of flashing lights, or by lighting up an unusual combination of programme or option lights. The manual explains the pattern for your model. Count the flashes, note which lights are on, or take a short video, which is easier than describing it.

Find your model number

The model number is on a rating label. On a front loader, look around the door opening, behind the filter flap or on the back; on a top loader, look under the lid or on the back. Your manual shows exactly where. The model number tells you, and us, exactly which code list applies. A photo of the label saves typing out a long string of letters and numbers.

Safe first steps

Safety first: only do the checks that match the code's family, and nothing that involves the inside of the machine. Don't open panels, test parts or try the service and test modes described online, which are designed for technicians. Never keep clearing a leak, overflow or heating code and carrying on.

  1. Record it. Photograph the code and note what the machine was doing when it stopped.
  2. Look it up. Check your manual or our brand guides for what it means on your model.
  3. Do the simple checks for that family from the table above: the tap, the hoses, the filter, the door, the load or the detergent.
  4. Clear it once, unless it's a leak or overflow code. Switch off at the wall for a few minutes, then switch on again. A one-off glitch, often after a power cut, may not return. With a leak or overflow code, switch off at the wall (or at the DB board if the plug or socket is wet or you'd have to stand in water), close the tap and call a technician instead.
  5. Test with a short programme. If the same code comes back, stop using the machine and book a technician.

Clearing a code versus fixing it

Switching off at the wall clears the display, not the cause. If a drain code keeps returning, the pump is struggling every time you run the machine. If a heating code returns, your washing isn't getting the hot wash you chose, and some heating faults go on to trip the power. A code that comes back is the machine telling you, accurately, that something needs fixing.

What the technician does with it

To a technician, the code is the starting point, not the answer. A drain code, for example, could be a blocked filter, a sock in the sump hose, a failed pump, a faulty level sensor or a board that isn't switching the pump on. The technician reads the stored fault history and runs the built-in test programme where the machine has them, then tests the parts in that family until the faulty one is confirmed. Only then do you get a quote.

That's also why the time and cost vary for the same code. Clearing a blockage or realigning a door is quick, a pump, inlet valve or door lock is normally fitted on the same visit when the part is available, and motor and board faults take longer. Our repair cost guide covers the factors that set the price.

Book a repair

When you get in touch, send the code, the model number and a photo of the display on WhatsApp, or include them in the online booking form. It helps the technician know what to expect. Code faults are handled under our front loader repairs and top loader repairs.

Questions and answers

Frequently asked questions

Can I clear a washing machine error code myself?
Often, yes: switching off at the wall for a few minutes clears many codes from the display. Whether it stays clear depends on the cause. If the same code returns after the simple checks, there's a real fault to fix.
My machine flashes lights instead of showing a code. What does that mean?
Machines without a digital display use patterns of flashing lights to show faults, and the manual lists what each pattern means. Count the flashes or take a short video. Send it to us with the model number when you book.
Does the error code tell you exactly which part is broken?
Not usually. It tells you which system has a problem, such as the drain, and the cause could be a blockage, a pump, a sensor or the board. Testing confirms which one, and the quote is based on that.
Is it safe to keep using my machine while it shows a code?
It depends on the code. An imbalance or foam code is usually safe to sort out yourself, and a heating or motor code may clear after one restart at the wall, but if it comes back, leave the machine off until it's checked. With a leak or overflow code, switch off at the wall, or at the DB board if the plug, the socket or the floor around them is wet, then close the tap and call straight away. If the machine trips the power, leave it off and call a technician.
Why did an error code appear after load shedding?
A cycle cut off by a power failure can leave water in the drum and an unfinished programme, and some machines show a code or a power-failure notice when the power returns. Switch off at the wall for a few minutes and restart. If a different code keeps appearing, the surge may have damaged something.
My code isn't in any of your guides. What now?
Check the manual for your model first, because it's the most reliable source. If you don't have it, send us the code, the brand and the model number when you get in touch. The technician can then check it against your exact model.

Book a technician

Still not working? We'll come to you.

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za