Skip to content

Common washing machine problems

Washing machine not spinning

A washing machine not spinning is often protecting itself: the load is out of balance, the water hasn't drained, or the door or lid isn't confirmed locked. If those are fine, worn carbon brushes, a broken belt or a motor fault are next. Here's how to narrow it down.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. Why a machine refuses to spin
  2. Match the symptom to the cause
  3. Likely causes in more detail
  4. Safe checks you can do
  5. Signs to stop using the machine
  6. What the technician checks and fixes
  7. How long the repair usually takes
  8. Keeping the spin working
  9. Book a spin repair

Why a machine refuses to spin

Before a fast spin, a modern machine runs a short series of checks. The tub must be empty of water, the door or lid must be locked, and the load must be spread evenly enough that the drum won't thrash about at high speed.

To judge the balance, the machine tumbles the load slowly and measures how evenly the drum turns. If it's lopsided, the machine redistributes the washing and tries again, then spins at a lower speed or gives up. The job is to find out which check it's failing, or which drive part has worn out.

Match the symptom to the cause

What you noticeWhat it usually points to
Washes normally, but the final spin is slow, short or skippedAn unbalanced load, too many suds, or a programme with little or no spin
Water left in the drum at the endA drain problem: the machine won't spin until the water has gone
Stops before the spin with the door symbol flashingThe door lock or lid switch isn't confirming
Motor hums or runs, but the drum stays stillA snapped or slipped drive belt, or a worn coupling or clutch on a top loader
Drum turns weakly or jerks, with a burning smellWorn carbon brushes or a motor fault
Nothing turns and there's no hum at allThe motor, its speed sensor, the wiring or the control board

Likely causes in more detail

An unbalanced load

This is the most common reason, and the easiest to fix. One heavy item on its own, such as a bath mat, a pair of jeans or a single duvet, ends up on one side of the drum and the machine can't even it out. Very small loads are harder to balance than mixed ones. Many machines show an unbalance code or symbol when this happens.

Water still in the drum

A machine won't spin while it still holds water. If water is left at the end, the fault is in the drain, so start with our guide to a washing machine not draining.

Suds and spin settings

Foam cushions the drum and makes the motor work harder, so many machines add extra rinses and hold the spin until the suds die down. Too much detergent, or hand-washing powder in a front loader, is the usual cause. Wool, delicates and hand-wash programmes spin gently or not at all, and a "no spin" option or a spin speed turned right down leaves clothes wet even when nothing is broken.

The door lock or lid switch

Front loaders won't spin unless the door lock confirms the door is shut and locked, and on top loaders the lid switch or lid lock does the same job. On a top loader, a failed lid switch can let the machine fill and wash but stop it at the spin. On a front loader, a worn lock tends to stop the cycle starting or cut it off partway.

Worn carbon brushes

Many machines with a conventional brushed motor have two carbon brushes that press against a spinning part of the motor and wear down over the years. As they get short, the drum turns weakly, jerks or stops on the spin, sometimes with a burning smell. Direct drive and inverter motors, used on many LG and Samsung front loaders, don't have brushes.

A broken or slipping drive belt

On belt-driven machines, a rubber belt links the motor to a large pulley on the back of the drum. If it snaps or comes off, the motor runs but the drum doesn't turn. A belt that keeps coming off is a warning sign in itself, because the pulley may be loose or the drum bearings may be wearing.

Top loader drive parts

Depending on the design, a top loader turns its agitator or pulsator through a drive coupling, a clutch or a gearbox. When one of them wears, you'll often hear the motor running while the drum barely moves, or the machine agitates but won't spin up.

Motor, speed sensor or control board

The motor itself, the sensor that reports its speed, the wiring between them and the board that drives the motor can all fail. Surges, especially when electricity returns after load shedding, can damage the motor control electronics. These faults need electrical testing, so they're strictly a technician's job.

Safe checks you can do

Safety first: do these checks with the machine switched off at the wall, unless a step says to run a programme. Don't tilt the machine, take off the back panel or go looking for the belt: the drive parts sit right next to live wiring and are a technician's job.

  1. Check the programme and spin speed. Make sure you haven't picked a delicate, wool or no-spin setting, and that the spin speed isn't turned to its lowest.
  2. Rebalance the load. Once the door unlocks, spread the washing out, take out one heavy item or add a couple of towels to a small load, then run a spin-only or rinse-and-spin programme.
  3. Look for water and foam. If water is left in the drum, follow the drain guide. If there's a lot of foam, run a rinse without detergent and use less next time.
  4. Close the door or lid properly. Make sure nothing is caught in the door seal and the door clicks shut. On a top loader, check that the lid closes fully.
  5. Make sure it stands firm. A machine that rocks can't keep the drum balanced, so it may refuse to spin up. If it moves when you push down on opposite corners, adjust the feet as your manual describes until it stands steady, then lock them.
  6. Write down any code. An unbalance or motor code narrows things down, and our washing machine error code guides explain the common ones.

Signs to stop using the machine

Switch off at the wall and leave it for a technician if you notice a burning smell, smoke or a crackling sound, if the drum grinds or scrapes as it turns, or if the machine trips the earth leakage. Don't keep restarting a spin that won't run either. Each attempt with a heavy, wet load strains the motor, and a slipping belt or a worn brush only gets worse.

What the technician checks and fixes

The technician rules out the simple causes first, then runs a spin test to see where the machine stops. With the panels off, they inspect the belt and pulley, measure the brushes, test the door lock signal, check the motor windings and speed sensor, and confirm the board is driving the motor properly.

  • Brushes: replaced as a pair, with the motor checked for wear.
  • Belt: refitted or replaced, and the pulley and bearings checked so it stays on.
  • Door lock or lid switch: replaced and tested through a full spin.
  • Top loader drive: a worn coupling or clutch replaced. A worn gearbox costs more, so you'll hear the options first.
  • Motor, sensor or board: repaired or replaced. On an older machine you'll be told plainly if the repair isn't worth it, and our repair or replace guide can help you decide.

Most of this work comes under our front loader repairs and top loader repairs.

How long the repair usually takes

Brushes, belts, door locks and lid switches are usually fixed on the same visit when the part is available. Motor and board faults take longer to diagnose, and some boards are made for one model only, so if a part has to be ordered, you'll know before you agree to anything. Our page on repair costs explains what affects the price.

Keeping the spin working

Book a spin repair

Still soaking wet after the checks? Call us, or send a booking request, and a technician will come to you, find the cause and quote before starting. Your repair carries our 6-month warranty on parts and labour. If the spin is loud as well as weak, read our guide to a washing machine noisy when spinning too.

Questions and answers

Frequently asked questions

Why are my clothes still soaking wet after the wash?
Either the machine skipped or shortened the final spin, or it never drained properly. Check the spin setting and the load balance first, then look for water left in the drum. If both look fine, a worn part is stopping the drum reaching full speed.
Why does my machine spin with some loads but not others?
Balance is almost always the reason. A small load with one heavy item, like a bath mat or a pair of jeans, is the hardest to balance, while a mix of large and small items spreads out evenly. If it struggles with every load, have the shock absorbers and motor checked.
Is a broken motor the usual reason a machine won't spin?
No. Load balance, drainage, the door lock, carbon brushes and belts are all much more common causes than a failed motor. That's why it pays to diagnose the machine properly before assuming the worst.
Can load shedding stop my washing machine spinning?
It can, in two ways. A programme cut off mid-cycle may need restarting before it reaches the spin, so once the power is back, try a spin-only or drain-and-spin programme. If it still won't spin, the surge when the power returned may have damaged the board that drives the motor, which needs a technician to test.
Why does my washing machine smell of burning when it tries to spin?
Worn carbon brushes, a slipping belt or an overheating motor are the usual causes. Stop using the machine, switch it off at the wall and have it checked, because running it can damage the motor further.
Why does my top loader agitate but not spin?
The lid switch or lid lock is the first suspect, because the machine won't spin unless it knows the lid is shut. A worn clutch, a slipping belt or water that hasn't drained can do the same. If the lid closes properly and the water has gone, the switch and drive parts need testing.
How full should I load my front loader?
Fill the drum loosely, leaving roughly a hand's width of space at the top. A packed drum can't tumble or balance properly, while a very small load is easily thrown off balance. Your manual gives the maximum load for each programme.
Why does my machine try to spin, stop and start again?
That's the machine trying to balance the load: it slows down, tumbles the washing and tries again. If it gives up after a few attempts, rearrange the load or run a spin-only programme. If it happens with every load, the shock absorbers, the motor or its speed sensor may need checking.

Book a technician

Still not working? We'll come to you.

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za