Skip to content

Common washing machine problems

Washing machine not draining

A washing machine not draining usually has a blockage between the drum and your drain: a clogged pump filter, a kinked or blocked hose, or a blocked standpipe. If those are clear, the drain pump itself may have failed. Start with the safe checks below.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. How your machine gets rid of water
  2. Signs the drain is the problem
  3. Likely causes, most common first
  4. Safe checks before you call
  5. When to stop and call a technician
  6. What the technician checks and fixes
  7. How long a drain repair takes
  8. How to stop it happening again
  9. Book a drain repair

How your machine gets rid of water

At the end of each wash, and before every spin, the control board switches on the drain pump. The pump draws water from the bottom of the tub through a filter, sometimes called the coin trap, and pushes it up the drain hose into your standpipe or sink trap. A pressure sensor tells the board when the tub is empty.

The board gives the pump a set time to do this. If the water hasn't gone by then, most machines stop the programme. Depending on the model, you'll see a drain code, a flashing light or a door that stays locked, with water still in the drum.

Signs the drain is the problem

  • Grey water standing in the drum when the programme ends or stops.
  • The cycle stops before the spin, or the washing comes out dripping.
  • Water goes down much more slowly than usual, or the machine gurgles as it drains.
  • A hum or buzz from the bottom of the machine with no sound of water moving.
  • A drain code on the display, such as LG OE, Samsung 5C or Bosch E18.
  • A stale, swampy smell from water left sitting in the filter and sump.

Likely causes, most common first

A clogged pump filter

Most front loaders have a filter behind a small flap at the bottom front. It catches lint, hair, coins, hair clips, buttons and the odd baby sock before they reach the pump, and once it's packed, water can't get past. It's the first thing to check on any front loader that won't drain.

Top loaders vary. Some have a filter at the bottom front like a front loader, some have a lint filter inside the drum, and some have none you can reach. Your manual shows which kind you have.

A kinked, squashed or clogged drain hose

Pushing the machine back against the wall can fold the drain hose flat behind it. Hoses also narrow over the years as lint and detergent sludge build up inside, especially at the end that joins the sink trap. A hose that's higher or longer than the manual allows makes the pump work harder too.

A blocked standpipe, sink trap or household drain

Sometimes the machine is pumping perfectly and the water simply has nowhere to go. If the sink next to the machine drains slowly, or grey water comes back up the standpipe, the blockage is in the plumbing. Some sink traps are sold with the washing machine spigot sealed, to be cut open when the hose is fitted, so a brand-new connection may still be closed.

A jammed or failed drain pump

A coin or hair clip that slips past the filter can jam the pump's impeller or snap its blades, and pumps also wear out with age. A pump that hums without moving water is usually jammed or has a broken impeller. One that makes no sound at all may have failed or may not be getting power from the board, and telling those apart takes electrical testing.

Faults out of sight

Less often, the blockage is inside the machine, such as a sock lodged in the sump hose between the tub and the pump. The water level sensor or its thin pressure hose can also fail, so the machine doesn't realise water is still inside. On top loaders, a faulty lid switch can stop the cycle before the final spin and leave the washing soaking. All of these need a technician.

Safe checks before you call

Safety first: switch the machine off at the wall and unplug it before you touch the hose or the filter. If the last wash was hot, let the water cool first. Do only what your manual describes, never open panels or test anything electrical, and stop straight away if anything trips the power.

  1. Check the programme. Make sure the cycle has really finished and that no "rinse hold" option is selected, because it leaves the rinse water in the drum on purpose.
  2. Look behind the machine. Check that the drain hose isn't kinked, crushed or pushed too far down the standpipe. If you have to ease the machine forward to see it, empty it through the pump filter first (step 4), then slide it gently without pulling on the hoses or the cable.
  3. Test your drain. Run the tap in the sink next to the machine for a minute. If it drains slowly or water backs up the standpipe, a plumber needs to clear the blockage.
  4. Clean the pump filter as your manual describes. Lay down towels and a shallow tray, and expect more water than the tray can hold. If there's a small emergency drain hose beside the filter, empty the machine through that first. Then unscrew the filter slowly, clear out the lint and any objects, and refit it straight and hand-tight.
  5. Run a drain or spin programme. Plug in, switch on and watch the filter flap for drips. If the water goes, you've found the problem.
  6. Write down any code. Note or photograph what the display shows. It saves time when you book.

When to stop and call a technician

  • The filter and hose are clear and the machine still won't drain.
  • The pump hums, buzzes or stays silent when it should be draining.
  • The filter cap won't turn, or your model has no filter you can reach.
  • There's a burning smell, or water is leaking from under the machine.
  • The earth leakage or a breaker trips when the machine runs. Leave it unplugged, because that can mean a dangerous fault.
  • The door is locked with water inside. Don't force it: a broken handle or lock adds to the repair.

What the technician checks and fixes

The technician starts by draining the machine safely. Then they work along the drain path: the filter housing, the sump hose, the pump and its impeller, the drain hose and your standpipe. They test whether the pump is getting power from the board and whether its motor runs, and check the water level sensor and its pressure hose.

  • Blockage: cleared, then proved with a test drain and spin.
  • Jammed or worn pump: cleared or replaced, one of the routine washing machine parts replacements.
  • Hose set-up: rerouted to the right height, or a damaged hose replaced. If the trouble started after a move, our washing machine installation service sets it up properly.
  • Sensor or control fault: confirmed by testing first, because a pump that never gets the signal to run looks just like a failed one.

We fix drain faults on all major brands, including Defy, Hisense and Whirlpool.

How long a drain repair takes

Clearing a blocked filter or hose is usually quick once the water is out. A new pump is normally fitted on the same visit when the part is available; if it has to be ordered, the technician tells you before you agree to the repair. The price depends on whether a part is needed and on your machine's brand and model, and our guide to what affects repair prices explains the rest.

How to stop it happening again

  • Empty pockets before every wash: coins, hair clips and paper tissues are common causes of a blocked filter.
  • Wash underwired bras, baby socks and other small items in a mesh laundry bag.
  • Clean the pump filter every few months, or as often as your manual suggests, and more often if you wash work clothes, pet bedding or sandy towels.
  • Use the detergent dose on the pack for your load size. Too much leaves sludge in the hose and sump.
  • Run a hot maintenance wash with the drum empty once a month. Our guide to why your washing machine smells explains why it helps.

Book a drain repair

Water that won't drain often brings other symptoms with it. A machine won't spin with water inside, so see washing machine not spinning if your washing is soaking. Most front loaders also keep the door locked until the water has gone, which our guide to a washing machine door that won't open covers.

If it still won't drain after the checks, call or WhatsApp us, or book a technician online. They'll find the cause at your home and quote before any work starts.

Questions and answers

Frequently asked questions

Can I keep using my washing machine if it isn't draining?
Not until the cause is fixed. Every new cycle adds water to a machine that can't get rid of it, works a struggling pump harder and risks a flooded floor. Switch it off at the wall and leave it until the water can be drained safely.
How do I get the water out before the technician arrives?
Switch off at the wall and unplug first. On most front loaders the water comes out through the pump filter, or a small emergency drain hose beside it, as your manual describes, so lay down towels and a shallow tray. On a top loader you can scoop most of it into a bucket with a jug, or simply leave it for the technician, who drains the machine before starting work.
Why does my machine drain slowly but eventually empty?
A partly blocked filter, a hose narrowed by lint and sludge, or a slow household drain are the usual reasons. A worn pump that has lost some of its strength can do it too. Clean the filter and test the sink first, and if it's still slow, have the pump checked before it fails completely.
Is it normal to find water when I open the pump filter?
Yes. Some water always sits in the filter housing and the bottom of the tub, so expect some to run out even when the machine drained properly. It's only a problem if the drum itself still holds water after the programme ends.
Can a blocked kitchen sink stop my washing machine draining?
Yes, if the machine drains into the sink trap or into a standpipe on the same pipe. The machine pumps normally, but the water backs up or drains so slowly that the programme times out. If the sink is slow too, a plumber clearing the drain is the fix, not a washing machine repair.
My machine stopped draining after it was moved. Why?
The drain hose is the first suspect: it may be kinked behind the machine, pushed too far into the standpipe, or sitting higher than the manual allows. A new sink connection that was never opened has the same effect. Our installation service can set the hose and drain up correctly.
What does it mean if the machine hums but no water moves?
The pump is being switched on but can't turn freely or move the water. Usually something is jammed in it or the impeller has broken, and occasionally the pump motor has failed. Switch off at the wall, unplug and clean the filter first, with towels and a tray ready, and if the hum continues, leave the machine off and have the pump tested.
Is a drain repair expensive?
Not usually. Clearing a blockage is mostly labour, while a new pump adds the cost of the part, which varies by brand and model. You get a quote before any work starts, and the call-out fee is R300, only payable if you decide not to go ahead with the quote.

Book a technician

Still not working? We'll come to you.

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za