Skip to content

Brands we repair

AEG washing machine repairs

Our AEG washing machine repairs start with a proper test, not a guess. A technician comes to your home in Gauteng, diagnoses your AEG front loader, washer-dryer or integrated machine, and quotes before any work starts.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. About AEG washing machines
  2. Warning signs on an AEG
  3. AEG faults we repair
  4. Codes on the AEG display
  5. Simple checks for AEG owners
  6. Why we test before replacing parts
  7. Integrated AEG machines
  8. Keeping an AEG in good shape
  9. Areas and booking

About AEG washing machines

AEG is a German brand with a long history in electrical engineering, and its household appliance business has belonged to the Swedish Electrolux group since 1994. AEG washing machines are premium front loaders and washer-dryers, freestanding or built in. Ranges such as the 6000, 7000 and 8000 series add features like ProSense load sensing, ProSteam steam refresh and ÖKOMix, which AEG says pre-mixes the detergent with water before it reaches the clothes.

That sophistication is good for your clothes, but it means more sensors and electronics, so careful diagnosis matters. Because AEG and Electrolux machines come from the same group, many share engineering and some parts. The data plate carries the model number, the product number code (PNC) and the serial number, and the technician uses these to identify the exact part for your machine.

AEG machines are part of our washing machine repairs service, done at your home anywhere in our Gauteng areas.

Warning signs on an AEG

Book a technician if your AEG:

  • trips the mains switch or earth leakage when it runs;
  • won't switch on at all;
  • won't drain, or stops with water in the drum;
  • shows a code on the display;
  • leaks water onto the floor;
  • no longer dries the laundry, if it's a washer-dryer;
  • makes unusual noises, especially on spin;
  • smells bad, even after a hot wash; or
  • gives you a tingle or a shock when you touch it.

Safety first: if the machine trips the electricity, don't keep resetting the trip switch. Leave the machine switched off at the wall until a technician has tested it. Beyond the simple checks in your manual, never open an AEG or test its parts yourself, because the electronics inside run on mains power.

AEG faults we repair

Draining and water intake

Blocked pump filters, kinked hoses and worn drain pumps cause most drain faults (see our drain fault guide). Fill faults come from the tap, low water pressure, the filter in the inlet hose connection or the inlet valve (see when water won't come in).

Door locks

If the door lock fails, the machine won't start, or the door stays locked when the programme has finished. Our page on a washing machine door that won't open explains what you can safely try.

Heating and sensors

Cold washes, or programmes that run far longer than usual, can point to the heating element or the temperature sensor.

Leaks

On an AEG, the first places to look are the door seal and the hoses at the back. A seal that has split, or that has a sock or coin caught in its folds, lets water out at the front, while a hose that has worked loose drips behind the machine. Water from underneath is more often the drain pump or a seal inside the tub. See finding the source of a leak.

Spin and balance

Before every spin, an AEG measures how evenly the laundry is spread around the drum. If it's lopsided, the machine tumbles the load to spread it out, then spins slowly or skips the spin rather than shake itself across the floor. Bath mats, jeans and other heavy items washed on their own are the usual trigger. If the spin stays weak with a mixed, sensible load, the drain, the motor or its control electronics need testing. See a weak or missing spin.

Noise and bearings

A rumble that rises with the spin speed usually means worn drum bearings, while knocking can be something trapped between the drum and the tub. See rumbling and knocking on the spin.

Electronics

Boards and displays can fail, sometimes after a power surge when the electricity comes back after load shedding. Switching the machine off at the wall while the power is off reduces that risk, as our article on protecting your washing machine from load shedding explains. The technician tests before replacing a board, because the fault is not always where it seems.

Washer-dryers

An AEG washer-dryer that washes well but leaves the laundry damp has a fault on the drying side, so the technician tests that side on its own. Our page on drying problems on washer-dryers explains the parts involved.

Codes on the AEG display

Look the code up in the manual for your exact AEG, because codes change between models and generations. The PNC on the data plate tells the technician exactly which version you have, so photograph the plate together with the display and send both to us. While you wait, our guide to a washing machine showing an error code explains which first steps are safe.

Simple checks for AEG owners

Before you book, and with the machine switched off at the wall, it's worth ruling out the simple things:

  • The plug point works: unplug the machine and test the socket with a lamp.
  • The tap is fully open and the inlet hose has no kinks.
  • The drain hose isn't flattened behind the machine, and the pump filter is clean (your manual shows how to drain and open it: unplug first, have towels and a shallow tray ready and let hot water cool).
  • The door is properly shut, with nothing caught in the seal.
  • No delayed start or child lock is set.
  • The load suits the programme: delicate and wool programmes take much smaller loads than cottons.

Why we test before replacing parts

On a sensor-rich machine like an AEG, one fault can show up as several symptoms. A drain problem can look like a spin problem, and a faulty sensor can make a good heater look broken. Replacing parts on a guess wastes your money, so the technician confirms the cause first, then quotes for the part that has actually failed. The PNC on the data plate makes sure the replacement is the right one for your exact machine. See washing machine parts replacement.

Integrated AEG machines

Many AEG machines are built into kitchen cabinetry, with a cabinet door fixed to the front. They need more time than a freestanding machine, because the machine has to come out of its space before the repair and go back in afterwards, with the cabinet door lined up and the hoses checked for leaks. Tell us when you book that the machine is integrated, and clear the area in front of the cabinet, so the technician can allow enough time and get straight to work.

Keeping an AEG in good shape

  • Read the manual. AEG programmes, steam options and load sensing work as intended only when they're used as intended, and the manual explains which programme suits which fabric.
  • Clean the filter, drawer and seal. With the machine unplugged, clean the pump filter as the manual shows, rinse the drawer and wipe the door seal regularly.
  • Check for leaks. Look under and behind the machine now and then, and check the hoses for bulges or cracks.
  • Don't overload it. Stick to the capacity for each programme. On a washer-dryer, the drying capacity is smaller than the washing capacity, so dry in smaller batches.
  • Use the right detergent. Use a low-suds detergent made for front loaders, measured to the load.

For a professional check of an older machine, see washing machine servicing.

Areas and booking

We repair AEG washing machines across Johannesburg, Pretoria, Centurion, Sandton, Midrand and the East Rand.

Bookings are by phone or WhatsApp on 079 895 0496, or through the form on our contact page. Send the model number and PNC from the data plate, a photo of any code, and let us know if the machine is integrated so the technician can allow enough time.

ProServ is an independent repairer. We are not affiliated with, authorised or endorsed by AEG. AEG is a trademark of its owner and is used here only to describe the machines we repair. If your machine is still under the manufacturer's warranty, contact AEG first, because outside repairs may affect that warranty.

Four simple steps

How it works

  1. Contact us

    Call or WhatsApp with your machine brand and what it is doing. A photo of the error code helps.

  2. A technician comes out

    We book a time that suits you, and on urgent call-outs we aim to arrive within 1 hour, depending on where the technician is working.

  3. Diagnose and quote

    We find the fault and give you a clear price before any work. The R300 call-out fee is only payable if you decide not to go ahead with the quote.

  4. Repair

    Most repairs are done on the spot when the part is available, and every repair carries our 6-month warranty.

Questions and answers

AEG washing machine repair questions

My AEG gives me a shock when I touch it. What should I do?
Stop using it straight away. Switch off at the wall and unplug it if you can reach the plug without touching the machine; if you can't, switch the power off at the DB board instead, and don't touch the machine until the power is off. A shock usually means an earth fault or water reaching an electrical part, so a technician needs to test it before it is used again.
Where is the PNC on my AEG?
It is on the data plate, which on AEG washing machines is behind the door or behind the filter door at the bottom front. Send us a photo of the whole plate when you book.
Is an AEG worth repairing?
Usually, yes, as long as the part for your machine's PNC can still be found, which the technician checks before quoting. If an older AEG needs bearings and a control board at the same time, the sums change, and you'll hear that before you decide.
What does ProSense do on my AEG?
ProSense is AEG's load-sensing system. It weighs the laundry and adjusts the programme time, water and energy to suit, which is why the time on the display can change after the wash has started. That's normal, and not a sign of a fault.
Does a smelly door seal on my AEG need replacing?
Not usually. Most smells come from residue and lint in the folds of the seal, which you can wipe out before running an empty hot wash. A seal needs replacing when it has split, or when black mould has stained deep into the rubber and keeps coming back.
My AEG hums but won't drain. What does that mean?
A hum with no water moving usually means the drain pump is trying to run but something is blocking it, often a coin, button or hair clip caught in the filter. Switch off at the wall and unplug, then clean the filter as your manual describes, with towels and a tray ready and any hot water given time to cool. If the filter is clear and it still hums, the pump has probably failed and needs a technician.

Book a technician

AEG washing machine playing up?

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za