Skip to content

Common washing machine problems

Washing machine door won't open (or won't lock)

When a washing machine door won't open, it's usually because the machine is keeping it locked: there's water inside, the drum is turning, or the lock is still releasing. If it stays shut after that, or won't lock at all, the lock, catch or handle has probably failed.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. How the door lock works
  2. Why the door won't open
  3. Why the door won't lock
  4. Safe things to try first
  5. Signs the lock or catch has failed
  6. What the technician does
  7. How long it usually takes
  8. Avoiding door trouble
  9. Get the door open

How the door lock works

Every front loader has a door lock, sometimes called an interlock. When you press Start, it locks the door and tells the control board the door is safely shut, and only then does the machine fill. It stays locked while there's water in the drum, while the drum is turning and, on many models, while the water inside is too hot to open safely.

When the programme ends, many locks take a minute or two to release, so a short wait is normal. Modern top loaders often lock the lid during the spin as well, while older ones use a lid switch that stops the spin when the lid opens. Either way, the lock is there to keep hands away from a spinning drum and water inside the machine.

Why the door won't open

The cycle hasn't really finished

If the machine is still draining or doing a final spin, or you paused it partway, the lock stays on. Check the display or the programme lights before assuming there's a fault.

Water left in the drum

A machine that can't drain keeps the door locked, so it doesn't open onto a flood. If you can see water through the glass, the real problem is the drain. See washing machine not draining.

Hot water inside

If you pause or stop a 60°C or 90°C wash partway, some machines keep the door locked until the water has cooled or drained, so you can't open it onto hot water. Give it time, or let the machine drain.

Child lock

The child lock locks the buttons and, on some models, the door as well. Look for a key or lock symbol on the display.

A power cut mid-cycle

If load shedding or an outage stopped the machine partway, the door may stay locked until the power returns and the machine can drain. Even if it does open, there may be water and hot washing behind it, so wait for the electricity.

A broken handle, catch or lock

If the handle feels loose or moves without any resistance, the handle mechanism has probably snapped. If the machine has drained, the drum is cool and the door still won't release, the lock or the signal from the board has most likely failed.

Why the door won't lock

The opposite problem stops the machine starting at all. The display lights up and you press Start, but nothing happens: the door symbol flashes, the lock clicks over and over, or a door code appears. The usual reasons are:

  • The door isn't pushed firmly shut, or laundry or a fold of the seal is caught in it.
  • The plastic hook on the door, which the lock grabs, is bent, cracked or broken off.
  • Worn hinges let the door drop, so the hook no longer lines up with the lock.
  • The lock itself has failed, or the board isn't sending it the signal to lock.
  • On a top loader, the lid switch or lid lock has failed, or something stops the lid closing fully.

Safe things to try first

Safety first: never prise the door with a screwdriver or knife, pull hard on the handle or reach in behind the seal. You can break the handle or the hook, tear the seal and turn a small repair into a bigger one. Don't take panels off to reach the lock, and never tamper with it.

  1. Wait. Give the machine a few minutes after the programme ends, and longer if you stopped a hot wash partway.
  2. Check for water. If there's water in the drum, choose the drain or spin programme on the machine's own controls and let it finish. If it won't drain, follow our drain guide.
  3. Turn off the child lock if a lock or key symbol is showing, using the buttons your manual gives.
  4. Switch off at the wall for a few minutes, then back on, and try the drain or spin programme once. After a power cut, this often lets the machine finish and release the door.
  5. For a door that won't lock, open it, check that nothing is caught between the door and the seal, and close it firmly until it clicks.

Don't try to force or release the lock any other way. A drum with water in it floods the floor the moment the door opens, so if the machine won't drain and unlock on its own, switch off at the wall and leave it for the technician.

Signs the lock or catch has failed

  • The door stays locked long after the cycle, with no water inside and a cool drum.
  • The lock clicks repeatedly, or a door code comes back every time you start a wash.
  • The handle moves freely without opening the door.
  • The hook on the door is visibly cracked, bent or missing.
  • The door sags when it's open, or you have to lift it to close it.

What the technician does

The first job is to get your washing out safely. The technician drains the machine if needed, then releases the lock from inside the machine without damaging the door or the seal. Next they test the lock and the signal reaching it from the board, and inspect the handle, the hook, the hinges and the door alignment.

  • Faulty lock: replaced and tested through a full cycle.
  • Broken handle or hook: replaced. On some models these come as part of the door frame.
  • Worn hinges: replaced or adjusted so the door lines up with the lock again.
  • Board or wiring fault: traced, then repaired or replaced once you've accepted the quote.
  • Lid lock or lid switch on a top loader: replaced. See top loader repairs.

For more on door locks and seals, see our front loader repairs page. The Whirlpool and AEG pages describe door faults on those machines.

How long it usually takes

Locks, handles and door hooks are small parts, and fitting them is usually quick, so the job is normally finished on the same visit when the part is available. If the part for your model has to be ordered in, you're told before you agree to the work. Board faults take longer to trace. How the price is worked out is explained in our repair pricing guide.

Avoiding door trouble

  • Close the door with a firm push rather than a slam.
  • Don't lean on the open door or let children swing on it. It wears the hinges and drops the door out of line.
  • Wait for the lock to release instead of tugging the handle.
  • Keep the seal clean, so fluff and residue don't stop the door closing.
  • If load shedding is due, only start a wash that has time to finish.

Get the door open

Washing stuck inside? Phone or WhatsApp us, or use our booking form. On urgent call-outs we aim to arrive within 1 hour, depending on where the technician is working. If a door or lid code is showing, our guides to Samsung error codes, LG error codes, Bosch error codes and Defy error codes cover the common codes for those brands.

Questions and answers

Frequently asked questions

How long should the door take to unlock after a wash?
On many machines it's a minute or two after the programme ends. If you stopped a hot wash partway, some models wait for the water to cool or drain first. If it's still locked well after that, with no water inside, the lock or its signal may have failed.
Is a door lock expensive to replace?
A door lock is one of the smaller parts on a washing machine and fitting it is usually quick, so it's normally one of the less costly repairs. The price depends on the brand and model. You'll get the exact figure in the quote before any work starts.
Why does my machine click but not start?
The click is usually the door lock trying to engage. If the lock can't confirm the door is shut, because the hook is damaged, the door is out of line or the lock has failed, the machine won't fill or start. Check that the door is closed firmly, then have the lock tested.
Can I open the door during a power cut?
It's safer not to try. Many doors stay locked until the power returns, and even one that opens may have water and hot washing behind it, ready to flood the floor. Wait for the electricity to come back and let the machine drain, and the door should release.
My door handle snapped. Can it be replaced?
Yes. On many front loaders the handle and its catch can be replaced on their own, while on some models they come with the door frame. The technician opens the door safely first, then fits the new part.
Does the child lock lock the door as well?
On some models it does, and on others it only locks the buttons. Look for a key or lock symbol on the display, and check your manual for the button to hold to switch it off.
Can I add washing after the cycle has started?
Many front loaders let you pause and add an item early in the cycle, but only if the water level and temperature are low enough. If the door doesn't unlock when you pause, the machine has decided it isn't safe yet. Let the cycle run and wash the item next time.
Why does water drip out when I open the door?
A little water trapped in the folds of the seal is normal and drips out when you open the door, so wipe the seal after the last wash of the day. If water runs out, or the floor gets wet during the wash, the seal may be damaged. See our guide to a washing machine leaking.

Book a technician

Still not working? We'll come to you.

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za