Skip to content

Common washing machine problems

Washing machine leaking: where it comes from and why

Is your washing machine leaking? Where the water appears usually tells you why: the door seal or detergent drawer at the front, the hose connections at the back, or a pump, hose or tub seal underneath. Before anything else, cut the power safely and close the machine's tap, as the first steps below explain.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. First steps when you find water
  2. Where is the water coming from?
  3. Leaks at the front
  4. Leaks at the back
  5. Leaks underneath
  6. Safe checks before you call
  7. When to stop using the machine
  8. What the technician checks and fixes
  9. How long a leak repair takes
  10. Preventing leaks
  11. Get a leak fixed

First steps when you find water

Safety first: water and electricity don't mix, so switch the machine off at the wall before you touch it or mop around it. If the plug, socket or cable is wet, or you'd have to stand in water to reach the switch, don't touch them: turn the power off at the DB board instead, provided you can get to it without standing in water, and keep children and pets away.

  1. Cut the power safely. If the plug and socket are dry and you don't have to stand in water to reach them, switch off at the wall and unplug the machine. If not, switch off at the DB board as above and leave the plug alone until it has dried and been checked.
  2. Close the washing machine tap. It's usually on the wall behind or beside the machine, and closing it stops a split hose or a faulty valve from adding more water.
  3. Dry the floor. Mop up, put towels down and lift any rugs. In a flat or an upstairs unit, check whether water could be reaching the home below.
  4. Think about when it happened. Water that appears while the machine fills, washes, drains or spins points to different parts, so it's worth noting.

Where is the water coming from?

Where the water isUsually whenLikely cause
Front, under the doorDuring the wash or spinDamaged or dirty door seal, laundry caught in the seal, too many suds
Top front, around the detergent drawerWhile fillingBlocked drawer or softener siphon, caked powder, overfilled compartments, high water pressure
Bottom front, by the filter flapAfter cleaning the filter, or while drainingFilter cap not screwed in straight, or a worn filter seal
Behind, at the tap or top backWhile filling, or all the timePerished hose washer, cracked or bulging inlet hose, loose connection
Behind, on the floor near the drainWhile drainingDrain hose out of the standpipe, a blocked standpipe overflowing, split drain hose
Underneath, towards the middleDuring the wash or spinPump, sump hose or internal hose, tub seal and bearings, cracked tub
Inside the drum, with the machine offOvernight or between washesAn inlet valve that isn't closing fully

Leaks at the front

The door seal

The rubber seal around a front loader's door folds back on itself, and the folds trap water, lint, hair and small items. Over time, underwires, coins and sharp objects nick or split the rubber, and mould and old detergent can perish it.

A sock caught between the seal and the glass holds the seal open and lets water out on every turn of the drum. If the door has dropped on worn hinges, it may not press evenly against the seal either.

The detergent drawer

When powder cakes in the compartments, the softener siphon blocks or the drawer housing clogs with residue, the incoming water backs up and spills out of the front. Very high mains pressure can push water out too, and so can filling a compartment past its MAX line.

Leaks at the back

The inlet hose screws onto the tap at one end and the machine at the other, with a rubber washer sealing each connection. Those washers flatten and perish with age, and over-tightening can crack the plastic nuts. The hose itself can split or bulge, and a bulging hose is a warning sign, because it can burst and flood a room in minutes.

At the drain end, the hose can jump out of the standpipe when the pump pushes water through it hard. A standpipe that's partly blocked can also overflow onto the floor behind the machine every time it drains.

Leaks underneath

Water from under the machine is usually coming from a part inside it. The common culprits are the drain pump and its seal, the sump hose that joins the tub to the pump, and the smaller hoses that carry water from the drawer to the tub. If the floor by the filter flap is wet, check the filter cap first.

A leak from the middle of the machine, especially with a rumble on the spin and rust-coloured water underneath, can mean the seal behind the drum has failed and water is reaching the bearings. Our article on the signs of worn washing machine bearings explains this in detail.

Less often, the outer tub itself has cracked or been holed. An underwire trapped between the drum and the tub can pierce it, and a drum knocking about on collapsed bearings or a broken drum spider can crack it. Some machines also have a leak sensor in the base that stops the machine and shows a code when water collects there.

Safe checks before you call

With the power off and the floor dry, you can safely check a few things yourself:

  • Hand-tighten the inlet hose connections at the tap and at the machine. Don't use tools, and stop if a nut is cracked.
  • Look along the inlet hose for splits, bulges or perished rubber. If you find damage, keep the tap closed until the hose has been replaced.
  • Make sure the drain hose is secure in the standpipe or sink trap, and that the standpipe isn't overflowing.
  • Check that the pump filter cap is screwed in straight and firmly, as your manual describes.
  • Pull back the folds of the door seal and look for holes, splits or trapped items, and clean out any fluff and residue.
  • Take out and clean the detergent drawer and its housing.

Don't run the machine again to find where the leak starts. Keep the tap closed and the machine off, take a photo of where the water was, and note what the machine was doing when you found it. That tells the technician where to start looking, which saves time when they trace the leak.

When to stop using the machine

  • Water has reached the plug, the socket or the cable.
  • The earth leakage or a breaker trips. Leave the machine off, because water may have reached an electrical part.
  • The water is coming from inside the machine rather than a hose connection.
  • You can hear a rumble on the spin as well as seeing a leak.
  • Water is spreading under kitchen units, into a wall or through to a neighbour below.

What the technician checks and fixes

The technician dries the area, runs the machine under controlled conditions and, with the panels off, traces the water back to its source. Then they fix the cause, not just the symptom.

  • Door seal: replaced, which on some models means taking the front panel off.
  • Inlet or drain hoses: replaced, with new washers and a check of the tap.
  • Pump, sump hose or internal hoses: resealed or replaced.
  • Detergent drawer and housing: cleared, or a cracked part replaced.
  • Tub seal: replaced together with the drum bearings, because water getting past the seal ruins them. Our page on a washing machine noisy when spinning explains what the bearing job involves, including on sealed tubs.
  • Cracked outer tub: replaced where it makes sense, or you'll be told honestly if a new machine is better value.

Most of these are routine washing machine parts replacements. If the leak started after the machine was installed or moved, our washing machine installation service puts the connections right. We fix leaks on all major brands, including Bosch, AEG, Siemens and Defy.

How long a leak repair takes

Hoses, washers, filter seals and drawer blockages are usually sorted on the first visit, and door seals and pumps are normally fitted on the same visit when the part is available. Bearings and tubs take several hours, and if parts have to be ordered in, you'll hear about it before you agree to the repair. For what drives the price, see our guide to how repair costs are worked out.

Preventing leaks

  • Check the inlet and drain hoses once a year, and replace any that look cracked, bulging or stiff.
  • Close the washing machine tap when you go away for more than a day or two.
  • Wipe the door seal after the last wash of the day and leave the door ajar so it dries, unless young children or pets can get to the machine.
  • Clean the detergent drawer every few weeks, and use the dose on the pack.
  • Keep the machine level, so it doesn't walk on the spin and stretch its hoses.

Get a leak fixed

Leaks are worth fixing quickly. Call or WhatsApp us, or book a leak repair. On urgent call-outs we aim to arrive within 1 hour, depending on where the technician is working, and you'll get a quote before any work starts. If water is also left in the drum, see why a machine won't drain.

Questions and answers

Frequently asked questions

Is a leaking washing machine dangerous?
It can be, mainly because of the electricity. Water that reaches the plug, the socket or the wiring inside the machine can cause a shock or trip the power, and a steady leak damages floors and cupboards. Treat it as urgent and keep the machine off until it's fixed.
Can I use my washing machine if it's only leaking a little?
It's safer not to. Small leaks usually get bigger, water can reach electrical parts inside the machine, and some causes, like a failing tub seal, damage the bearings while you keep using it. Keep the tap closed and the machine off until it's been checked.
Why does it only leak during the spin?
Spin leaks often point to the drain hose being pushed out of the standpipe by the force of the water, a loose hose inside the machine, or a worn tub seal. A split near the bottom of the door seal can also show up mainly at speed. Note whether the water is at the back, the front or underneath, and tell the technician.
Why is there water in the drum when the machine is off?
The inlet valve is probably not closing fully, so water seeps in from the tap between washes. Left alone, it can fill the drum until it overflows, so close the tap and have the valve checked. Our guide to a washing machine not filling with water explains how the valve works.
Can a torn door seal be repaired, or does it need replacing?
A torn or split seal needs replacing. Patches and sealants don't last on a part that flexes and gets wet on every wash. On some models the front panel has to come off to fit a new one, so it's a technician's job.
Why does water come out of the detergent drawer?
Usually the drawer or its housing is clogged with old powder and softener, so water can't flow through properly. High water pressure and overfilled compartments can cause it too. If it still spills after a thorough clean, have the inlet valve and the water pressure checked.
How can I tell if the leak is from the machine or the plumbing?
Dry everything, then look at the tap, the hose and the standpipe while the machine is off. A drip from the tap itself, the pipe behind it or the standpipe is a plumbing problem. A drip where the hose screws on, or anywhere along it, usually means a perished hose washer or a damaged inlet hose, because the hose stays under mains pressure whenever the tap is open. If everything stays dry with the machine off, the leak is in the machine or its hoses, so close the tap and leave the machine off until a technician has traced it.
Can too much detergent make a machine leak?
Yes. Excess suds can push past the door seal and out of the drawer, especially in front loaders. Use the dose on the pack and a detergent made for automatic machines, not hand-washing powder.

Book a technician

Still not working? We'll come to you.

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za