Skip to content

Washing machine repair services

Front loader repairs at your home

Front loader repairs are done at your home, whether the machine won't drain, spin, heat or unlock, or leaks or roars on the spin. The technician finds the failed part and quotes before work starts, and most repairs are finished on the same visit when the part is available.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
Illustration of a front loader washing machine with its door open and a spanner beside it
On this page
  1. How a front loader works
  2. Front loader faults, by symptom
  3. Quick checks before you book
  4. What the technician checks
  5. Is a front loader worth repairing?
  6. What affects the cost
  7. Looking after a front loader
  8. Front loader brands we repair

How a front loader works

The drum lies on its side inside an outer tub that holds the water. The tub hangs from springs at the top of the cabinet and rests on shock absorbers underneath, with heavy counterweights bolted on to keep it steady when the drum spins at speed.

The drum's shaft runs through two bearings at the back of the tub, behind a seal that keeps the water out. On a belt drive machine, a motor under the tub turns the drum through a belt and a large pulley. On a direct drive machine, the motor is built onto the back of the tub and turns the shaft itself.

Water comes in through an electric inlet valve, flushing the detergent drawer on the way. A pressure sensor tells the control board when the level is right, a heating element under the drum warms the water, and the drain pump pulls it out through a filter at the end. The door lock keeps the door shut until the drum has stopped and the water has gone.

Front loader faults, by symptom

Each symptom below usually points to a few parts, and links to our fuller guide.

A rumble, roar or bang on the spin

A rumble that grows into a roar as the drum speeds up is the classic sign of worn bearings. Banging is more often worn shock absorbers, a loose counterweight or a bunched load, and a scrape on every turn can mean an underwire is caught between the drum and the tub. Our guides to a washing machine noisy when spinning and the signs of worn washing machine bearings help you tell them apart.

Water left in the drum

If the cycle stops with grey water inside, something is in its way: a packed pump filter (on some machines called the coin trap), a kinked drain hose, a blocked standpipe, or a pump that has jammed or burnt out. Don't force the door, which normally stays locked while water is inside. See washing machine not draining.

The door won't open, or won't lock

The door lock holds the door shut and tells the control board it's safe to fill. When it fails, the machine clicks and won't start, or finishes the wash and won't let you in. A broken handle, a bent catch or a door that has dropped on worn hinges can do the same. See washing machine door won't open.

The drum won't turn or won't spin

A front loader won't spin until the water has drained and the load is balanced, so rule those out first. After that, the usual suspects are worn carbon brushes, a belt that has slipped off or snapped, a faulty speed sensor, or the motor and the electronics that drive it. See washing machine not spinning.

Leaks at the front or underneath

Water at the front usually comes from a split door seal, or a sock caught between the seal and the glass. Underneath, look to a pump filter that wasn't screwed in fully, a leaking pump or sump hose, or a failed shaft seal at the back of the tub. See washing machine leaking.

Detergent left in the drawer

Powder or liquid left in the drawer after the wash means the water isn't flushing it through. Caked powder, residue blocking the jets above the drawer, low water pressure or detergent in the wrong compartment is the usual reason. Failing those, the section of the inlet valve that feeds that compartment may have failed.

A knock, wobble or rattle from the drum

The drum's plastic paddles can crack or work loose and rattle with every turn. On many front loaders, the metal bracket on the back of the drum that carries the shaft, called the drum spider, can also corrode and crack, letting the drum wobble and knock much like worn bearings.

Cold washes, or the power trips when it heats

If a 60°C wash comes out cold, the heating element or its temperature sensor is the first suspect. An element that has broken down inside can trip the earth leakage as soon as it switches on, which is why some machines trip only on hot programmes.

Safety first: if the earth leakage or a breaker trips while the machine is running, switch the machine off at the wall, unplug it and leave it off until a technician has checked it. Tripping can be a sign of a dangerous electrical fault, so don't keep resetting it.

No power, or a code on the display

A dead machine may have lost its supply, blown its mains filter or had its control board damaged by a surge after load shedding (see washing machine won't turn on). A code points to an area, such as the drain or the door, rather than to one part: start with washing machine showing an error code and our LG error codes, Samsung error codes, Bosch error codes and Defy error codes guides.

Quick checks before you book

  • The plug is in and switched on at the wall, and the house has power (try a lamp in the socket if you're unsure).
  • No delay timer or child lock is set (look for a clock or key symbol on the display).
  • The door is shut firmly with nothing caught in the seal, and the tap is fully open with no kinks in the hoses.
  • If water is left inside, clean the pump filter as your manual describes, after switching off at the wall and unplugging. Expect a lot of water, so lay down towels and a shallow tray first, and give the water time to cool if the machine stopped partway through a hot wash.

What the technician checks

  1. What happened. When it started, what the display showed, and whether there was a power cut or the machine was moved. The answers often point straight at the fault.
  2. The basics. The socket, tap, hoses and standpipe are checked first, and stored fault codes are read on machines that keep them.
  3. The suspect parts. With the machine switched off and unplugged, the pump, door lock, heater and motor are tested, and the brushes, bearings and door seal are checked for wear.
  4. The quote. You hear what has failed, what the repair involves and what it costs before any work starts, including whether the part has to be ordered.
  5. The repair and a test run. A test programme checks filling, heating, draining and spinning, and the floor is checked for drips before the technician leaves.

Is a front loader worth repairing?

Usually. Pumps, door locks, carbon brushes, door seals, heating elements, inlet valves and shock absorbers are routine parts designed to be replaced, and fitting one costs far less than a new machine.

Bearings need more thought. Where the outer tub unbolts into two halves, new bearings and a seal can be fitted on their own, but on many newer machines the halves are welded together, so a complete new tub and drum assembly is needed instead. In that case, or on an older machine with other wear, weigh the quote against a new machine with our repair or replace guide.

What affects the cost

The part, and the time it takes to reach it, decide most of the price. A cleared blockage may need no part at all, while bearings mean stripping the machine down to the tub, and a built-in machine has to come out of its cabinet first.

The call-out fee is R300, only payable if you decide not to go ahead with the quote. Every repair carries a 6-month warranty on parts and labour, and our repair cost page explains how repairs are priced.

Looking after a front loader

  • Use a low-suds detergent made for automatic or front loading machines, at the dose on the pack.
  • Empty pockets, and wash underwired bras in a mesh bag: coins, hair clips and underwires cause many pump blockages and drum noises.
  • Wipe the folds of the door seal after the day's last wash, and leave the door ajar so the drum can dry, unless small children or pets can reach the machine.
  • Mix big and small items so the drum can balance, and keep within the load your manual gives.
  • Run an empty hot maintenance wash about once a month, especially if you mostly wash cold.
  • Switch off at the wall during load shedding, as our guide to protecting your washing machine from load shedding explains.

Our article on why washing machines smell covers odours, and washing machine servicing explains what a yearly check-up looks at.

Front loader brands we repair

With 20 years of washing machine repair experience, we work on front loaders from all major brands, including Bosch, Defy, LG, Samsung, Siemens, AEG, Miele, Smeg, Hisense and Whirlpool. The layout is similar from brand to brand, but the details differ: many LG front loaders use direct drive, for example, while plenty of others turn the drum with a belt. Have the model number handy when you book a front loader repair.

Four simple steps

How it works

  1. Contact us

    Call or WhatsApp with your machine brand and what it is doing. A photo of the error code helps.

  2. A technician comes out

    We book a time that suits you, and on urgent call-outs we aim to arrive within 1 hour, depending on where the technician is working.

  3. Diagnose and quote

    We find the fault and give you a clear price before any work. The R300 call-out fee is only payable if you decide not to go ahead with the quote.

  4. Repair

    Most repairs are done on the spot when the part is available, and every repair carries our 6-month warranty.

Questions and answers

Front loader repairs: questions we get asked

How long does a front loader repair take?
When the part is available, a drain pump, door lock, set of carbon brushes or heating element is normally fitted on the same visit. Bearings take several hours, because the machine is stripped down to the tub. If a part has to be ordered, you're told before you agree to the repair.
Does a front loader need special detergent?
Yes. A front loader tumbles the washing through very little water, so it needs a low-suds detergent labelled for automatic or front loading machines. Hand-wash powder makes far too many suds, which can leak from the door, spoil the rinse and leave residue behind.
Why does the door stay locked for a minute or two after the wash?
That's normal on many front loaders. Many locks use a small heated element that has to cool before the door releases, and the machine also waits for the drum to stop and the water to drain. If it's still locked five minutes later with no water inside, the lock may be faulty.
What are the black marks in the folds of my door seal?
They're usually mould, growing on detergent and fabric softener residue in the damp folds. Wiping the folds after washing and running a monthly hot maintenance wash stop it spreading. Marks that have soaked deep into the rubber may never come out, and a seal that is split or perished should be replaced.
Does my front loader have to come out of its space for a repair?
Usually it's pulled forward so the technician can reach the top and back panels. If it's built into a cabinet, has a dryer stacked on top or stands in a tight space, mention it when you book so enough time is set aside.
Why does my front loader take so long to finish a wash?
Long programmes are normal on many modern front loaders, because eco programmes save water and electricity by washing for longer at lower temperatures. Extra suds or repeated rebalancing add time too. If it stalls on the same step every time, suspect a heating, draining or sensor fault.

Book a technician

Washing machine broken? Let's get it fixed.

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za