Skip to content

Common washing machine problems

Washing machine won't turn on

When a washing machine won't turn on, the cause is often outside it: a dead socket, load shedding, empty prepaid units or a tripped supply. Inside the machine, a damaged mains filter, power cable or control board is most likely. Start with the checks below, which don't involve opening anything.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. Dead, or just not starting?
  2. Check the power supply first
  3. Settings that make a machine seem dead
  4. Common causes inside the machine
  5. Safe checks before you call
  6. Load shedding and surges
  7. What the technician tests and repairs
  8. Time and cost
  9. Get it working again

Dead, or just not starting?

What happensWhere to look
Completely dead: no lights, no display, no soundThe power supply, socket, plug or cable first, then the machine's mains filter, power switch or board
The display lights up but Start does nothingChild lock, delay start, a door that isn't shut properly, or the door lock
Clicks or hums, then nothingThe door lock trying to engage, or a fault on the control board
Starts, then cuts out mid-cycleA loose plug or multi-plug, a supply problem or an internal fault
Trips the earth leakage or a breakerA fault inside the machine: leave it off and call a technician

Being precise about what the machine is doing helps, because each version points somewhere different. It's also the first thing a technician will ask you.

Check the power supply first

Is the house power on? During load shedding, or after a fault in your street, the obvious can catch anyone out. On a prepaid meter, check that you still have units. If the lights and other plugs work, look at the machine's own socket: make sure the wall switch is on and the plug is pushed fully in.

Then plug a lamp or a phone charger into the same socket. If that doesn't work either, the socket or its circuit is the problem, and that's a job for an electrician rather than a washing machine technician. If the machine is plugged into a multi-plug or an extension lead, move it to a wall socket and try again.

Settings that make a machine seem dead

  • Child lock. A key or lock symbol means the buttons are locked. Your manual shows which button to hold to turn it off.
  • Delay start. If a timer is set, the machine waits before starting and may show a countdown. Cancel it as your manual describes.
  • The programme dial. On a machine with a dial, check that it points at a programme and not at Off.
  • Standby. Many machines switch the display off after a few minutes without use. Press the power button again before you choose a programme.
  • The door. Most front loaders won't start until the door is pushed firmly shut and the lock engages. If yours won't lock, see washing machine door won't open or lock.

Common causes inside the machine

Mains filter

Many washing machines have a small suppression filter where the power cable enters the machine. Its job is to stop electrical interference, and a surge can blow it, leaving the machine completely dead. A failing filter can also trip the earth leakage.

Power cable and plug

Cables get crushed when a machine is pushed back against the wall, or chafed when it walks on the spin. Plugs can overheat and scorch, especially in a loose or worn socket. Any damage here means the machine mustn't be used until it's repaired.

Power switch or button board

On some models the power button sits on its own small board. The button, that board or the cable linking it to the main board can fail, so pressing it does nothing.

Control board

The control board runs everything, including its own power supply. Surges, especially when electricity returns after load shedding or an outage, can damage that supply or other parts of the board. Water from a leak dripping onto the electronics can do the same, which is why a leak and a dead machine sometimes go together. Some boards can be repaired, while others have to be replaced.

Door lock

If the display lights up but the machine won't go any further, the door lock may not be confirming that the door is shut. You might hear it click over and over, or see a door symbol flash.

Safe checks before you call

Safety first: these checks only involve the socket, the plug and the machine's own buttons. Never open the machine, take off the back panel or test wiring yourself, and never use a machine whose cable or plug is damaged.

  1. Confirm the house has power, and on a prepaid meter, that you have units.
  2. Check the wall switch and the plug. Switch on at the wall and push the plug in fully, in a wall socket rather than a multi-plug.
  3. Test the socket with a lamp or a phone charger.
  4. Look at the plug and cable without pulling on them. If you see scorch marks, melting or cuts, switch off at the wall, unplug and leave the machine for a technician.
  5. Check the DB board. If the earth leakage or a breaker has tripped, unplug the washing machine and leave it off. Don't plug it in or switch it on again to test it, even if the switch resets: a machine that trips the power can have a dangerous fault, so it needs a technician.
  6. Try the controls. Turn off the child lock, cancel any delay timer, close the door firmly and press Start.
  7. After a power cut, switch off at the wall for a few minutes, then back on, and try once more. If it still won't respond, it needs testing.

Load shedding and surges

Power interruptions are hard on washing machines. When electricity returns to an area the voltage can spike or flicker, and the board and mains filter take the hit. A machine cut off mid-cycle can also be left with water in the drum and the door locked.

Switching off at the wall when the power goes, and waiting a few minutes after it returns before switching on, reduces the risk. A good plug-in surge protector, rated for the machine's full load and plugged straight into the wall socket rather than a multi-plug, adds another layer. Our guide to protecting your washing machine from load shedding covers it in more depth.

What the technician tests and repairs

A technician starts at the socket and works inwards. They confirm the supply, check the plug, cable and mains filter, test the power switch and the board's power supply, and look for scorched connectors or signs that water has reached electrical parts. If the machine trips the power, they test the main components, such as the heating element, to find the one that's leaking current to earth.

Mains filters, cables, switches and door locks are straightforward parts to replace. A control board is more involved: the technician checks whether it can be repaired and what a replacement would cost, and if water caused the damage, the leak gets fixed too. See washing machine parts replacement for the parts we fit, on all major brands from Samsung and LG to Hisense and Defy.

Time and cost

Supply, plug and filter faults are often found and fixed on the first visit. Boards are specific to each model, so if yours has to be ordered, the technician says so up front, before you agree to the repair. The part is the biggest factor in the price: a mains filter or switch is a small repair, while a board for a premium machine sits at the top of the scale. Our pages on how repair costs add up and repairing or replacing a machine help you weigh it up.

Get it working again

If the socket works and the machine is still dead, book a repair by phone, WhatsApp or the online form. Our R300 call-out fee is only payable if you decide not to go ahead with the quote, and the repair is covered by our 6-month warranty on parts and labour.

Questions and answers

Frequently asked questions

My washing machine stopped working after load shedding. Can it be fixed?
Usually, yes. The mains filter and the board's power supply are the parts a surge commonly damages, and both can be tested and replaced. Leave the machine switched off at the wall until a technician has seen it.
Why does my washing machine trip the electricity?
A heating element leaking current to earth is a classic cause, along with a damaged cable, a failing mains filter or water reaching an electrical part. Either way, the earth leakage is a safety device doing its job. Leave the machine unplugged and have it tested before you use it again.
Why do the lights come on but the machine won't start?
Check the child lock and any delay timer, and make sure the door is pushed firmly shut. If those are fine, the door lock may not be engaging or the board may not be responding to the buttons. Both need testing by a technician.
Can I plug my washing machine into an extension lead?
It's safer not to. A washing machine draws a heavy current when it heats water, and extension leads and multi-plugs can overheat or make the machine cut out. Plug it straight into a wall socket that's in good condition.
Why does my machine switch off in the middle of a cycle?
A loose plug, a worn socket or a multi-plug can lose the connection when the machine vibrates, and dips in the supply can do it too. If the plug and socket are sound and it keeps happening, an internal connection or the board needs testing.
Can a burnt plug be the reason my machine is dead?
Yes. A scorched or melted plug usually means a poor connection that has overheated, and it can damage the socket as well. Don't use the machine: switch off at the wall and have the plug, the cable and the socket checked.
My machine was dead, then started working again. Should I worry?
It's worth having it checked if it happens more than once. Faults that come and go usually come from a loose connection, a failing switch or a board on its way out, and they rarely fix themselves. Note when it happens and what the display shows, because that helps the technician find it.

Book a technician

Still not working? We'll come to you.

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za