Skip to content

Blog

How to protect your washing machine from load shedding and power surges

By ProServ

Illustration of a washing machine plugged into a surge protector, with a lightning bolt symbol
On this page
  1. Why outages harm washing machines
  2. Habits that protect your machine
  3. Surge protection that works
  4. Running it on backup power
  5. After the power comes back
  6. Signs of surge damage
  7. Can surge damage be fixed?
  8. The bottom line

To protect your washing machine from load shedding and power surges, start with the moment the power comes back, because that’s often when the damage happens. Load shedding has eased a great deal since its worst years, but power cuts haven’t gone away in Gauteng. Load reduction still switches off some areas at peak times, and municipal faults, cable theft, transformer failures and summer storms take suburbs off the grid without warning. Modern washing machines are full of electronics, and every outage ends with a restart they’d rather do gently.

Here’s why outages and surges damage washing machines, the habits and devices that protect them, how to run one on backup power, and what to do if yours has stopped working after an outage.

Why outages harm washing machines

The surge when the power returns

When power is restored to an area, it doesn’t always come back smoothly. There can be a brief spike, or the supply can flicker on and off a few times while everything in the area switches on at once. The control board, its power supply and the mains filter (the part that smooths electrical interference on the way in) are the most exposed to those spikes.

Low voltage and brownouts

Sometimes the supply dips well below normal instead of spiking. Motors and electronics don’t cope well with low voltage, so the machine may stop mid-cycle, show an error or behave strangely until the supply recovers.

Lightning in summer storms

Gauteng’s summer thunderstorms bring a lot of lightning, and a nearby strike can send a large surge through the power lines. A plug-in surge protector helps with smaller spikes, but nothing plugged in is completely safe from a close strike. Unplugging is the only sure protection.

Stopping halfway through a wash

A cut in the middle of a programme can leave the machine stopped with water inside, and on many machines the door stays locked until the electricity is back. Most machines handle a single interruption well and resume or restart when the power returns. Repeated flickering while the machine is trying to restart is harder on the electronics and the door lock.

Habits that protect your machine

These cost nothing, and they prevent a lot of damage.

Switch off when the power fails

If the power goes off, or you know a cut is coming, switch the machine off at the wall socket. When the power comes back, wait a few minutes for the supply to settle before you switch on again. That way the machine isn’t connected for the spike or the flickering that can follow.

Plan long washes around known outages

Before you start a long programme, check whether a cut is likely: your area’s load reduction or load shedding schedule if one applies, and any planned maintenance notices from Eskom or your municipality. A standard cotton programme can run for two hours or more, so check the time on the display and use a quick programme when time is short.

Unplug when a storm is coming

Don’t start a wash with a thunderstorm building, and unplug the machine until the storm has passed. The wall switch alone isn’t enough here, because a lightning surge can jump the small gap inside a switch.

Surge protection that works

A quality plug-in surge protector

A good plug-in surge protector between the wall socket and the machine absorbs spikes before they reach the electronics. Choose one from a reputable supplier that is rated for the machine’s full load: a washing machine heating water can draw around 2,000 watts or more, and the rating plate on the machine gives the exact figure. Cheap multi-plugs with a “surge” label don’t always offer much protection. Plug the protector straight into the wall socket and the machine straight into the protector, and never run a washing machine from a multi-plug or extension lead.

The parts inside a protector that absorb surges wear out over time, and many protectors have an indicator light that shows whether the protection still works. Replace the protector when the light says so, or after a big surge.

Voltage protection with a delay

Some plug-in protectors also disconnect the machine when the voltage goes too high or too low, and only reconnect it a little while after the supply is back to normal. That suits areas with frequent outages, because it deals with both the flickering and the brownouts for you.

Protection at the DB board

A registered electrician can fit surge protection at your distribution board (DB board), which protects every appliance in the house, not just the washing machine. It’s worth asking about if you’ve had several appliances damaged, and it’s a job for an electrician only.

Running it on backup power

You can run a washing machine on a home inverter, a solar system or a generator, but a few points matter:

  • Heating is the big load. A machine heating water can draw around 2,000 watts or more, and many home inverter systems aren’t sized for that on top of everything else. A cold wash draws far less, because heating the water takes most of the power. Any programme that heats, including 30°C and eco settings, switches the element on at full power, so on battery power choose a cold wash. A washer-dryer runs a heater for a long time when drying, so save drying for when grid power is on.
  • The type of inverter matters. A pure sine wave inverter gives the cleanest supply. Modified sine wave inverters and some generators produce a rougher supply that can upset sensitive electronics.
  • Generators need care. Run a portable generator outdoors, well away from doors and windows, because its exhaust contains carbon monoxide. Have it connected to the house through a changeover switch fitted by a registered electrician, rather than running the washing machine from it on an extension lead.
  • The changeover can cause a blip. Some systems take a moment to switch between grid and battery, and some machines notice it and stop or restart.
  • Use the sun. If you have solar panels, run the machine in the middle of a sunny day, when the panels produce the most.

If you’re not sure your system can run the machine safely, ask your installer before you try.

After the power comes back

If the power went off mid-wash:

  1. Switch the machine off at the wall.
  2. Wait until the power has been back and steady for a few minutes.
  3. Switch on. Many machines resume the programme by themselves. If yours doesn’t, choose a rinse and spin or a drain programme to finish and empty the drum.
  4. If the door stays locked with water inside, don’t force it. Let the machine drain first, and if it still won’t release, see washing machine door won’t open.
  5. If the earth leakage or circuit breaker trips when you switch the machine on, leave it off and call a technician. This can indicate a dangerous fault.

If the water was off too

Water and power outages sometimes come together. When the water supply returns, air and sediment in the pipes can slow the fill or block the machine’s inlet filter, so run the nearest cold tap until the water is clear before starting a wash. If the machine then shows a water supply error or won’t fill, the washing machine not filling with water guide covers the next checks.

Signs of surge damage

Rule out the supply first

A machine that seems dead after an outage isn’t always damaged. Check that it’s plugged in and switched on at the wall, that the rest of the house has power, and try a lamp in the same socket. If the machine is plugged into a surge or voltage protector, check that the protector has power and hasn’t cut the supply; voltage protectors wait a little while before reconnecting. If the lamp works and the machine still doesn’t, the fault is in the machine.

What damage looks like

  • No lights, no display, no response. The mains filter or the control board’s power supply may have failed. See washing machine won’t turn on.
  • It trips the electricity as soon as you switch on or when it starts to heat. Leave it off and call a technician.
  • A new error code that wasn’t there before the outage, or a display that behaves oddly. Note the code down, and see washing machine showing an error code for what codes mean.
  • It starts but won’t heat, drain or spin, which can mean part of the control board was damaged.
  • A burning smell. Switch off at the wall and leave it unplugged.

Please don’t open the machine to look for burnt parts. Testing electrical parts is a job for a technician.

Can surge damage be fixed?

Often, yes, and it isn’t always as bad as it looks. Sometimes a single part has failed, such as the mains filter; sometimes the main control board has to be replaced. A technician works from the plug inwards: the power cord and the supply reaching the machine, then the mains filter, the door lock, the heating circuit and the control board, using the machine’s own test mode where it has one. The fault is diagnosed before anything is replaced, and you get a quote before any work starts. Control boards are among the parts fitted through our washing machine parts replacement service.

If it’s a big repair on an older machine, weigh it up with our repair or replace guide. Some home insurance policies cover surge damage to appliances, so check yours before you decide.

The bottom line

The most effective protection costs nothing: switch off at the wall as soon as the power fails, then give the supply a few minutes to settle once it’s back before you switch on. Add a quality surge protector, unplug during thunderstorms, avoid starting long washes when a cut is likely, and take care running the machine on backup power. If yours has stopped working after an outage, it can often be repaired.

Machine dead after a power cut? Call or WhatsApp ProServ on 079 895 0496 or book online. We’ll test it properly and quote before any work starts.

Questions and answers

Frequently asked questions

If I use a surge protector, do I still need to switch off at the wall?
It's still worth doing. A surge protector absorbs spikes, but it doesn't stop the supply flickering on and off as it settles, and the parts inside it that soak up surges wear a little with every hit. Switching off costs nothing and keeps the machine clear of both.
Does an inverter protect my machine from power surges?
Not necessarily. Many home systems pass grid power straight through while it's on, so a spike on the grid can still reach the machine, and the surge protection built into inverters varies. Ask your installer what protection your system has, and keep using a plug-in protector or DB board protection either way.
Can my inverter and batteries run a whole wash?
Only if the inverter's continuous rating covers the machine's full draw on top of everything else that's running, and the batteries hold enough for the whole programme. A cold, quick programme is the easiest to fit within both limits. If the batteries do run flat mid-wash, the machine stops just as it would in a power cut, so restart it the same way.
Will a cold wash on backup power still get my washing clean?
For everyday loads, yes. Modern detergents are made to work in cool water, and a cold wash handles lightly and normally soiled clothes well. Keep towels, bedding and heavily soiled loads for a hot wash when grid power is back, and run a hot empty wash now and then to keep the machine fresh.
Should I unplug the machine when we go away?
Yes. With nobody home to switch it off when the power fails or a storm builds, unplugging is the simplest protection there is. Close the tap too, so a hose that gives way can't flood the floor while you're away.
What should I mention when I book a repair after a power cut?
Say when it stopped working (during the cut, as the power came back or in a storm), whether the earth leakage or a breaker tripped, and whether other appliances were damaged at the same time. Add any code on the display and the brand and model number. Those details point the technician to the likely cause before testing starts.

Book a technician

Washing machine broken? Let's get it fixed.

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za