Skip to content

Error code guides

Bosch washing machine error codes

Bosch washing machine error codes come in two styles: a letter and two digits, such as E18 (not draining) or E17 (water supply), and on many newer models a longer code with a suffix, such as E:36-25. This guide explains both, using Bosch's own support pages and manuals.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. Two styles of Bosch code
  2. Find the E-Nr on your Bosch
  3. Safe checks for common codes
  4. Common Bosch washing machine error codes
  5. Faults Bosch says you can't fix
  6. What the technician checks
  7. When to stop and call a technician
  8. If your code isn't listed
  9. Book a Bosch repair

Two styles of Bosch code

Many Bosch washing machines show a letter and two digits, and the same fault can appear in more than one form: Bosch's support pages pair the codes as E17 or F17 and E23 or F23, and say that F18 and d02 are the same fault as E18.

Newer Bosch machines use a longer code with a suffix, such as E:36-25 for a blocked drain pump or E:30-10 for a water supply problem, so note down both parts. Some faults on these machines show as a symbol instead: a tap symbol means the water pressure is too low, and a flashing door symbol means the door isn't closed properly.

Find the E-Nr on your Bosch

Bosch identifies each machine by its E-Nr (the model number) and an FD number that records when it was made. Both are on the rating plate, which Bosch puts inside the door, inside the maintenance flap or on the back, depending on the model. The manual for your E-Nr has the code table for your machine.

Siemens washing machines come from the same manufacturer and many use similar codes, but check your own manual first. See Siemens washing machine repairs if that's your brand.

Safe checks for common codes

Safety first: close the tap, then switch off at the wall and pull out the plug before you touch the drain pump or a hose. Bosch warns that water from a hot wash can scald, so let it cool before you open the service flap, and have towels and a shallow container ready.

Not filling: E17, E:30-10 or the tap symbol

Turn the tap fully on and check that the inlet hose isn't kinked or squashed behind the machine. With the tap closed, clean the small filters at the hose connection as your manual shows, then check the pressure at another tap.

Not draining: E18, E:30-80 or E:36

Check that the drain hose isn't kinked, trapped or routed too high, and that no unapproved extension has been added. Then clean the drain pump: open the service flap at the bottom front, drain the water through the small emergency hose into a container, put its sealing cap back on and press it down firmly, then unscrew the pump cover slowly and remove any fluff, coins or hair clips so the impeller turns freely. Screw the cover back on firmly. Then, as Bosch suggests, pour about a litre of water into compartment II of the drawer and run the drain programme to check for leaks.

Common Bosch washing machine error codes

Bosch washing machine error codes, meanings, likely causes and safe checks
Code What it usually meansLikely causesWhat you can safely check
E16 / F16 Door open The door isn't closed properly, or laundry is caught in it Close the door firmly; if the code stays, call a technician
E17 / F17 Water supply time exceeded: the machine didn't fill in time Tap closed, kinked inlet hose, blocked inlet filter or low water pressure Open the tap fully, straighten the hose and clean the inlet filter with the tap closed
E18 / F18 / d02 No drainage: the water isn't being pumped out A blocked drain pump or a kinked or blocked drain hose; if both are clear, a faulty pump Straighten the drain hose, then drain and clean the pump as your manual shows
E19 / F19 Heating time exceeded: the water didn't heat up in time A heating fault, such as the element or its temperature sensor Switch off at the wall and call a technician
E20 / F20 Unexpected heating: the machine heated when it shouldn't have A fault in the heating control Reset by switching the machine off and on; if it returns, call a technician
E23 / F23 Aquastop activated: the leak protection has stopped the machine Water leaking inside the machine, for example from a hose, the pump or a seal Switch off at the wall (at the DB board if the plug or socket is wet), close the tap and call a technician; don't keep resetting it
E25 / F25 Turbidity sensor faulty (it checks how cloudy the water is) A faulty sensor or connection Switch off at the wall and call a technician
E26 / F26 Analogue pressure (water level) sensor faulty A faulty sensor or connection Switch off at the wall and call a technician
F27 Pressure sensor faulty A faulty water level sensor or connection Switch off at the wall and call a technician
E28 / F28 Flow sensor faulty (it measures the water coming in) A faulty sensor or connection Switch off at the wall and call a technician
E:30-10 Water supply problem (newer models) Tap off, inlet hose kinked or jammed, inlet filters blocked, low water pressure, or a faulty water level sensor Turn the tap fully on, check the hose, clean the inlet filters and check the pressure at another tap
E:30-20 Critical malfunction (Bosch's manual gives no more detail) Too much detergent, or water added during the programme; otherwise a fault that needs a technician Turn off the tap, wait about 5 minutes for it to drain and restart; call a technician if it returns
E:36-10 / E:30-80 Water isn't being pumped out Drain hose routed too high, kinked, trapped or wrongly extended, or a blocked drain pipe or hose Check the drain hose against the installation instructions, clear any blockage and clean the drain pump
E:36-25 / E:36-26 Drain pump blocked Fluff, coins or small items caught in the drain pump Switch off and unplug, let hot water cool, then drain and clean the pump as your manual shows
E:38-25 / E:38-26 Drain pump blocked, or the inlet opening in the rubber door seal is blocked Fluff or debris in the pump or in the small opening in the door seal Run the drum clean programme, then clean the drain pump and the opening in the door seal as your manual describes
H:32 Spin stopped: the laundry is unevenly spread Laundry bunched on one side, or a single heavy item Spread the laundry out, mixing large and small items, and restart the spin
E:10-00 / E:10-10 / E:10-20 Automatic dosing pump blocked (models with i-DOS) The pump for the automatic detergent dosing system is blocked Clean the detergent drawer as your manual shows, and add detergent by hand until it's fixed

Faults Bosch says you can't fix

Bosch says the owner can't put right E19, E23, E25, E26, F27 or E28, which cover the heating, the Aquastop leak protection and the machine's sensors. For these, switch off at the wall (at the DB board if water has reached the plug or socket) and book a technician. E20 is worth one reset by switching off and on; if it returns, it needs a repair.

Take E23 seriously: Aquastop stops the water when it detects a leak, so clearing the code without fixing the leak lets water escape again on the next wash. If the earth leakage or breaker trips when the machine runs, leave it switched off until it has been checked.

What the technician checks

A Bosch repair starts with the code and the E-Nr. E18 and the E:36 codes lead to the drain pump, its housing and the hose run; E17 and E:30-10 to the inlet valve, the water level sensor and, where fitted, the flow sensor. For E23 the technician traces the leak to a hose, the pump, a seal or the tub before the leak protection is reset. Heating codes mean testing the element and its sensor.

You'll have a quote before any work starts. The call-out fee is R300, only payable if you decide not to go ahead with the quote, and a 6-month warranty covers the parts and labour. Our Bosch washing machine repairs page covers the wider faults on these machines, from door locks to bearings.

When to stop and call a technician

Stop using the machine and call us if a code keeps coming back after the simple checks, if there's water on the floor, a burning smell, or the machine trips the electricity. Codes that point to heating, sensors, the motor or the control board involve electrical parts, so please leave those to a technician.

WhatsApp us a photo of the display and the model number and we'll tell you what the code usually means on that model. For the full picture, see Bosch washing machine repairs, or read our general guide to a washing machine showing an error code.

If your code isn't listed

Bosch has made many generations of washing machines, and no single table covers them all. For a code your manual doesn't list, Bosch's newer manuals say to hold the on/off button for about five seconds to restart; if the code returns, unplug the machine for at least 30 seconds and book a repair, quoting the exact code. Our guides to a machine that won't drain and a machine that leaks cover the symptoms. ProServ is an independent repair business with no tie to Bosch; every meaning in the table comes from Bosch's published support pages and manuals.

Book a Bosch repair

Call or WhatsApp us with the code and the E-Nr, or fill in the form on our contact page. We aim to be with you within 1 hour on urgent call-outs, depending on where the technician is working. If the machine has stopped without a code, our main washing machine repair service page explains how a visit works.

Questions and answers

Bosch error code questions

Is F18 on a Bosch the same as E18?
Yes. Bosch says F18 and d02 are the same fault as E18: the machine isn't draining. Start with the drain hose and the drain pump, and book a repair if the pump still won't move the water.
What should I do when my Bosch shows E23?
Switch the machine off at the wall, or at the DB board if the plug or socket is wet, then close the tap and book a technician. E23 means the Aquastop leak protection has been triggered, and Bosch says it isn't a fault owners can fix.
Why does my Bosch show a tap symbol?
On newer Bosch machines the tap symbol means the water pressure is too low. Make sure the tap is fully open and the hose isn't kinked, then check the pressure at another tap. If the supply is good and it still shows, the inlet filters may be blocked or the valve may need testing.
What does H:32 mean on a Bosch washing machine?
H:32 means the spin stopped because the laundry was unevenly spread in the drum. Redistribute the load, mixing large and small items, and restart. If it happens with every load, have the machine checked for level and worn suspension parts.
Why does my Bosch show E:30-20 after a wash with extra detergent?
Bosch's manual calls E:30-20 a critical malfunction, but it also lists too much detergent and water added during the programme as causes. Turn off the tap, wait about five minutes for the machine to drain and restart it. If the code returns with a normal dose, book a repair.
Can I keep using my Bosch with an E19 heating code?
No. E19 means the water didn't heat up in the time allowed, so washes won't reach the right temperature, and Bosch says the owner can't fix it. Switch it off at the wall and have the heater and its sensor tested.
Where is the drain pump on a Bosch?
On Bosch front loaders it sits behind the service flap at the bottom front of the machine, with a small emergency drain hose beside it. Switch off at the wall, unplug and let any hot water cool before you open it, and keep towels and a container ready.

Book a technician

Bosch error code won't clear?

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za