Skip to content

Error code guides

LG washing machine error codes

LG washing machine error codes are short letter codes, such as IE, OE and UE, that show which part of the wash went wrong: water in, water out, balance, the door or the electronics. Here's what each one means in LG's own manuals, and what you can safely check.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. How LG shows a fault
  2. Reading the display correctly
  3. Find your LG model number
  4. Safe first checks
  5. Common LG washing machine error codes
  6. Codes that need a technician
  7. What our technician checks
  8. When to stop and call a technician
  9. If your code isn't listed
  10. Booking an LG repair

How LG shows a fault

An LG washer shows a fault as a code on the display and usually pauses or stops the programme. Most codes are two letters, and some add a number that narrows the fault down. A few are messages rather than faults: CL (child lock), tCL (tub clean reminder), Sud (too many suds) and PF (the power went off mid-cycle).

Front loaders, top loaders and washer dryers don't share one list. On LG front loaders AE means water is leaking inside the machine, but on some top loaders LG lists AE with LE as a drum rotation problem, and washer dryers add drying codes such as dHE.

Reading the display correctly

Digital displays build letters from short bars, so IE can read as 1E, and LG notes that vS can show as uS or u5. The number after a door code matters too: LG explains that dE1 means the door isn't closed properly, often with laundry caught in the seal, while dE2 means it's shut but hasn't locked.

On LG top loaders, a small uE during the spin means the machine is rebalancing the load, which LG says it tries up to three times by itself, so only step in if the cycle pauses. If UE appears at the very end of a front loader cycle, the clothes may be too wet to spin out: rearrange them, close the door and press Start/Pause.

Find your LG model number

Codes change between ranges, so the model number matters. On front loaders the label is usually inside the door opening or on the back panel; on top loaders, check the back or under the lid. LG publishes the owner's manual for each model on its support site, with the codes in the troubleshooting section.

Safe first checks

Safety first: switch off at the wall and unplug before you clean a filter or move a hose, and let the water cool after a hot wash. Never open panels or touch wiring.

  1. Write the code down, with any number after it and the point in the cycle where it appeared.
  2. Restart once, unless the code is FE, AE or tE. LG's advice for several codes is to unplug for 10 to 60 seconds and try again; if the same code returns, the cause is still there. FE and AE mean switching off at the wall and closing the tap straight away (if there's water near the plug or on the floor, switch off at the DB board instead and don't touch the plug), and tE means leaving the machine off for a technician.
  3. Do the check in the table below for your code: the tap and inlet hose for IE, the load for UE, the door seal for dE.
  4. For OE on a front loader, clean the drain pump filter as your manual shows. It sits behind the small cover at the bottom front: put down towels and a shallow tray, let the water out through the little drain tube first, then plug the tube and clip it back into place. Unscrew the filter slowly, rinse it and screw it back firmly.

Common LG washing machine error codes

LG washing machine error codes, meanings, likely causes and safe checks
Code What it usually meansLikely causesWhat you can safely check
IE Water inlet error: the drum hasn't filled in time Tap closed or partly open, kinked hose, blocked inlet hose filter, low pressure, a faulty inlet valve, or a leaking Aqua stop hose (red indicator) Open the tap fully, straighten the hose and clean the inlet hose filter with the tap closed
OE Drain error: the water isn't draining, or drains too slowly Kinked or blocked drain hose, clogged drain pump filter, too many suds or a failed drain pump Straighten the drain hose and clean the drain pump filter (switch off and unplug first, expect water)
UE Unbalanced load: the drum can't be balanced for the spin Load too small, one heavy item, laundry bunched on one side, an overfull drum or the machine not level Spread the load out, add one or two similar items to a small load and level the machine
dE / dE1 / dE2 / dE4 Door error: the door isn't closed properly or hasn't locked Laundry caught in the seal, door not pushed shut, an overfull drum, a bent or broken catch, or a faulty lock Clear the seal, close the door firmly, then switch off at the wall for a minute and restart
LE Motor locked: the drum isn't turning as it should An overloaded drum, or a coin or other item jamming it; otherwise a motor fault Reduce the load and leave the machine off for 30 minutes before restarting; if something is jammed between the drum and the tub, or LE returns, call a technician
tE Heating or temperature sensor error (LG's front loader manual calls it a control error) Usually a faulty temperature sensor (thermistor), or a heating fault Switch off at the wall and call a technician
FE Overflow: too much water in the drum An inlet valve that won't close, or extra water coming in through the detergent drawer Switch off at the wall and unplug (at the DB board if the plug or socket is wet), then close the tap and call a technician
PE Pressure sensor error: the machine can't read the water level A faulty water level sensor or connection Restart once; if PE returns, close the tap and call a technician
AE Water leak inside the machine on front loaders (a drum rotation problem on some top loaders) A loose or damaged inlet hose, a leak inside the cabinet or a faulty leak safety switch Switch off at the wall (at the DB board if the plug or socket is wet), close the tap and call a technician
vS (uS, u5) Vibration sensor error A failed sensor or a poor connection Press Start/Pause to carry on; if it returns, call a technician
CE Motor over-current: too much current in the motor circuit A short circuit, loose connection, earth fault or power surge Unplug for 10 seconds and retry; if it returns, close the tap and call a technician
PF Power failure: the power was cut during the cycle Load shedding, an outage or a loose plug Restart the programme once the power is stable
Sud Too many suds: the machine runs extra steps to clear the foam Too much detergent, or one that isn't low-suds (HE) Let it finish, then use less low-suds (HE) detergent
dHE Drying error on LG washer dryers A fault in the drying system Restart once; if it returns, call a technician
CL Child lock is on (not a fault) The child lock was switched on, sometimes by accident Hold the Child Lock button (or the two buttons marked with a lock) for about 3 seconds
tCL Tub clean reminder (not a fault) A prompt to run the Tub Clean programme Run Tub Clean with the drum empty

Codes that need a technician

LG's manuals tell owners to call for service on tE, FE, PE, vS and AE, and on a door code that won't clear. These involve sensors, valves, the door lock or a leak inside the cabinet, and finding the fault means testing parts that carry mains power.

Act quickly on two of them. With FE the machine is overfilling, so switch off at the wall, unplug it and close the tap straight away. With AE water is escaping inside the machine: switch off at the wall if the plug and socket are dry and you don't have to stand in water (otherwise at the DB board, without touching the plug), close the tap and keep children away from water on the floor. If the earth leakage or circuit breaker trips, leave the machine off until it has been checked.

What our technician checks

The technician confirms the code, asks when it appeared and tests the parts behind it before replacing anything. IE and FE lead to the inlet valve and water level sensor, OE to the drain pump, dE to the door lock and catch, and tE to the temperature sensor and heater. Balance and drive codes mean checking the suspension and, on direct drive models, the motor's position sensor and wiring.

You get a quote before any work starts, and if the part is available most repairs are finished on the same visit. The call-out fee is R300, only payable if you decide not to go ahead with the quote. Parts and labour are covered by a 6-month warranty. Our LG washing machine repairs page covers the wider faults on these machines, and there's more on how we repair front loaders, top loaders and washer-dryers.

When to stop and call a technician

Stop using the machine and call us if a code keeps coming back after the simple checks, if there's water on the floor, a burning smell, or the machine trips the electricity. Codes that point to heating, sensors, the motor or the control board involve electrical parts, so please leave those to a technician.

WhatsApp us a photo of the display and the model number and we'll tell you what the code usually means on that model. For the full picture, see LG washing machine repairs, or read our general guide to a washing machine showing an error code.

If your code isn't listed

Some LG models add codes of their own, such as the dispenser codes on machines with automatic dosing. Check your manual's troubleshooting pages or send us the code and model number, and see our guides to drain faults and water supply faults. ProServ is an independent repairer with no link to LG; the meanings in the table above come from LG's published manuals and support pages.

Booking an LG repair

Call or WhatsApp us with the code and model number, or use our contact page. We aim to arrive within 1 hour on urgent call-outs, depending on where the technician is working. If your machine has a fault but no code, start with the troubleshooting checks on our home page.

Questions and answers

LG error code questions

Why does my LG show IE when the tap is fully open?
IE means the drum didn't fill in the expected time, so the tap is only one part of it. A kinked hose, a blocked mesh filter in the hose or low water pressure in the house can all slow the flow. If the supply is good and the filter is clean, the inlet valve needs testing.
Is CL on an LG washer a fault?
No. CL means the child lock is on, and the buttons won't respond until you switch it off. Press and hold the Child Lock button, or the pair of buttons marked with a lock on some models, for about three seconds.
My LG showed PF after load shedding. Is it damaged?
Not necessarily. PF records that the power was cut during the cycle, and LG's advice is to restart the programme once the power is back. If the machine won't restart, or shows a different code when the power returns, get it checked.
Does an LE code mean the motor has failed?
Not always. LG links LE to an overloaded drum or something stuck in it, and advises leaving the machine off for 30 minutes before trying again. If LE keeps coming back with a normal load, the motor, its sensor or the wiring needs testing.
What does tCL mean on my LG?
tCL is a reminder to run the Tub Clean programme, not an error. Run it with the drum empty, adding a drum cleaning product if your manual calls for one. LG suggests running it about once a month.
Can I keep washing if my LG shows tE?
No. tE points to the temperature sensor or the heating control, so washes may not heat properly, and LG's manual says to unplug the machine and call for service. Switch it off at the wall and book a repair.
Why does my LG show OE when the drain hose isn't blocked?
The drain pump filter is the next place to look, because fluff, coins and hair clips collect there. Too many suds can also stop the pump moving water, so use less detergent. If the filter is clean and you can't hear the pump running, the pump itself may have failed.

Book a technician

LG error code won't clear?

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za