Skip to content

Error code guides

Defy washing machine error codes

Defy washing machine error codes appear mainly on Defy top loaders with a digital display, as a short code such as E1 (slow water intake) or E2 (slow draining). Many Defy front loaders show no numbered codes at all. Here's what Defy's own manuals say each code means.

  • Quote before any work starts
  • R300 call-out, only if you decline the quote
  • 6-month warranty on parts and labour
On this page
  1. Which Defy machines show codes
  2. Codes vary between Defy ranges
  3. Safe first checks
  4. Common Defy washing machine error codes
  5. Codes to leave to a technician
  6. What the technician checks
  7. When to stop and call a technician
  8. If your code isn't listed
  9. Book a Defy repair

Which Defy machines show codes

Defy top loaders in the DTL range show a fault as a short code on the digital display, though Defy notes that a code can take several minutes to appear.

Many Defy front loaders work differently. The manuals for the DAW381 and DAW388, for example, have no list of codes at all; they work through symptoms instead, such as the door not opening or the machine not filling. If a programme can't be started or selected, Defy explains that the machine may have switched to a self protection mode because of a supply problem, such as the mains voltage or the water pressure. Turning the programme knob to another programme cancels it.

Two other front loader behaviours look like faults but aren't. If a wash takes longer than the manual says, Defy's automatic foam absorption may be dealing with too much detergent. If the time stops counting down, the machine may be heating the water or correcting an unbalanced load.

Codes vary between Defy ranges

Defy has sold many ranges over the years, and the codes aren't the same across all of them. The manual covering the DTL148, DTL149, DTL150 and DTL161 lists E1 to E6, with E6 meaning the lid is open. The DTL165 keeps E1 to E5 but adds codes for the electronics, the heating, the lid lock, the inverter and the motor drive, plus a Por warning for the power supply.

That's why the model number matters. It starts with DTL on Defy top loaders and DAW on front loaders, and it's printed on a sticker on the cabinet, usually at the back, under the lid or inside the door opening. Defy publishes the manuals for its current machines, with the codes in the troubleshooting pages.

Safe first checks

Safety first: press the power button to switch off, then switch off at the wall and unplug before you touch a hose or a filter. Close the tap before you unscrew the inlet hose, and after a hot wash let the water cool before you open a front loader's filter. Never force a locked lid and never open the cabinet: Defy's own manual warns owners not to try to repair a machine that has stopped working.

  • E1, slow water intake: check that the tap is open and the municipal supply hasn't been cut, test the pressure at another tap and make sure the hot and cold hoses haven't been swapped. With the tap closed, rinse the small filter where the hose meets the machine.
  • E2, slow draining: make sure the drain hose isn't bent, isn't hooked too high and sits properly in the standpipe or sink, and check whether the power went off during the cycle, which Defy also lists as a cause.
  • E3, unbalanced: spread the laundry evenly around the tub so it isn't clumped on one side, and check that the machine stands level.
  • E6, lid open: on the DTL148, DTL149, DTL150 and DTL161, close the lid and check that nothing is stopping it closing.
  • Por, power warning: the mains voltage is too low or too high. Wait for the supply to settle, for example after load shedding, and plug the machine straight into a wall socket rather than an extension lead.

On a front loader with no code, the same basics apply: tap open, inlet hose straight, inlet filter clean, drain hose clear and the pump filter cleaned as the manual describes, with the machine unplugged, any hot water left to cool and towels and a shallow tray ready.

Common Defy washing machine error codes

Defy washing machine error codes, meanings, likely causes and safe checks
Code What it usually meansLikely causesWhat you can safely check
E1 Water intake is very slow Tap shut, supply cut off, low water pressure, a clogged filter at the inlet valve, or the hot and cold hoses swapped Open the tap, test the pressure at another tap, check the hoses are on the right taps and rinse the inlet filter with the tap closed
E2 Water drainage is very slow Drain hose badly positioned, bent or placed too high, a blockage in the hose or the drain pump (pump models), or a power failure Straighten and reposition the drain hose at the right height, check for blockages and check the power didn't go off
E3 Unbalanced load Laundry clumped on one side of the tub, or the machine not standing level Spread the laundry evenly around the tub and level the machine
E4 Overflow: too much water in the tub Water still coming in when it shouldn't, such as an inlet valve or water level fault Switch off at the wall (at the DB board if the plug or socket is wet), close the tap and call a technician
E5 Water level (pressure) sensor reading out of range A fault in the pressure sensor or its connection Switch off at the wall and call a technician
E6 Lid open (DTL148, DTL149, DTL150 and DTL161) The lid isn't closed, or something is stopping it closing Close the lid firmly and clear anything in the way
E8 Communication failure in the electronics (DTL165) A fault in the control electronics or their wiring Switch off at the wall and call a technician
Ec Zero-cross detection failure (DTL165) A fault in the way the control board senses the mains supply Switch off at the wall and call a technician
Ed Heating system failure (DTL165) A fault in the heater or its control Switch off at the wall and call a technician
EE Mechanical lid lock failure (DTL165) A broken lock, for example after the lid was forced open Don't force the lid; switch off at the wall and call a technician
EF Inverter failure (DTL165) A fault in the inverter that drives the motor Switch off at the wall and call a technician
EA Motor drive switch (TRIAC) failure (DTL165) The electronic switch that powers the motor has failed Switch off at the wall and call a technician
Por Power supply out of range (a warning) The mains voltage is too low or too high Wait for normal power and plug straight into a wall socket; if it keeps showing, call a technician
CL Child lock is on (not a fault) The child lock has been switched on Switch it off with the buttons your manual shows

Codes to leave to a technician

For E4, E5, E8, Ec, Ed, EE, EF and EA, Defy's manual gives one instruction: call for service. These codes involve the water level sensor, the control electronics, the heating, the lid lock and the motor drive, none of which an owner can safely test. Switch the machine off at the wall and note the code.

E4 means the machine has overfilled, so close the tap as well, and with EE don't pull on the lid, because the lid lock has already failed. If the earth leakage trips when the machine runs, leave it off until a technician has checked it.

What the technician checks

On a top loader with E1 or E5, the technician tests the inlet valve and the water level (pressure) sensor. E2 leads to the drain path: the hose, the drain pump on pump models or the drain valve on models that drain by gravity, and anything caught in between. An E3 that keeps coming back with a well-spread load can come down to worn suspension rods, which let the tub swing too far. Electronic codes such as Ec, E8, EF and EA mean testing the control board and the inverter before deciding what to replace.

You'll get a quote before any work begins. If the part is available, most repairs are completed on the same visit; if it has to be ordered, the technician tells you before you agree. The call-out fee is R300, only payable if you decide not to go ahead with the quote, and we give a 6-month warranty on parts and labour. Our Defy washing machine repairs page covers the wider faults on Defy front and top loaders, and our page on repairing top loaders explains how those jobs are done.

When to stop and call a technician

Stop using the machine and call us if a code keeps coming back after the simple checks, if there's water on the floor, a burning smell, or the machine trips the electricity. Codes that point to heating, sensors, the motor or the control board involve electrical parts, so please leave those to a technician.

WhatsApp us a photo of the display and the model number and we'll tell you what the code usually means on that model. For the full picture, see Defy washing machine repairs, or read our general guide to a washing machine showing an error code.

If your code isn't listed

Defy machines outside the ranges above may use different codes. Check the troubleshooting section of your manual, or send us the code (or a short video of the display) with the model number, and see our guides to water that won't drain and a drum that won't spin. We're an independent repairer with no connection to Defy, and the meanings in the table come from Defy's published manuals.

Book a Defy repair

Call or WhatsApp us with the code and model number, or use our contact page. We've been repairing washing machines for 20 years and come to homes in Johannesburg, Pretoria, Centurion, Sandton, Midrand and the East Rand. The ProServ home page explains the whole process.

Questions and answers

Defy error code questions

Why did my Defy take so long to show E1?
Defy's DTL165 manual says it can take 6 to 10 minutes for an error code to appear, so the delay is normal. Once E1 shows, check the tap, the water pressure and the inlet filter.
My Defy front loader shows no code. How do I tell what is wrong?
Many Defy front loaders, such as the DAW381, don't use numbered codes. Their manuals match symptoms to causes instead, for example a door that stays locked while there's still water in the drum. If that doesn't solve it, tell us what the machine is doing and send the model number.
What does Por mean on my Defy?
Por is a warning that the power supply is out of range, meaning the mains voltage is too low or too high. It can happen when the supply is unstable, for example around load shedding. If it keeps appearing while the rest of the house has normal power, have the machine checked.
Can I open the lid when my Defy shows EE?
Don't force it. EE means the mechanical lid lock has failed, and Defy's manual asks whether the lock is broken or the lid was forced open. Switch off at the wall and book a technician to free the lid and repair the lock safely.
Is E3 on a Defy top loader a serious fault?
Usually not. E3 means the load is unbalanced, so spread the laundry evenly around the tub and check that the machine is level. If it shows with every load, the suspension may be worn and needs a technician.
Does E2 mean my Defy's pump is broken?
Not necessarily. Defy lists a bent or badly placed drain hose, a hose hooked too high, a blockage and even a power failure as causes of E2. Check those first; if the water still drains slowly, a technician can test the drain pump, or the drain valve on models that drain by gravity, and clear the drain path.
Why does my Defy show E6?
On the DTL148, DTL149, DTL150 and DTL161, E6 means the lid is open. Close it firmly and make sure nothing, such as a sleeve, is stopping it shutting. If E6 stays with the lid closed, the lid switch needs checking.

Book a technician

Defy error code won't clear?

Call or WhatsApp now and we'll book a technician to come to you. You'll get a quote before any work starts.

info@proservwashingmachinerepairs.co.za